SET UP FOR USE
You can program the tuner to scan only the channels you
receive in your area.
CHANNEL SET UP (Automatic)
1
Plug in the VCR power cord
Plug the VCR power cord into a stand-
ard AC outlet. The "- : - -" indicator
flashes on the display.
Remembers:
●
If you use the VCR in an area with a voltage 110V-
127V, insert the power plug through the plug adapter
provided.
●
If your cable box or satellite box is connected as in
"Basic connections" on page 18 , you DO NOT have
to set up the channels. Just select the TV and VCR to
channel 3 or 4 and also have the CH3/CH4 switch on
the back of the VCR to match the channel you se-
lected (CH 3 or CH 4). Now select the Box to the
channel you wish to view or record.
2
Select channel 3 or 4 on the TV
Turn on the TV and set the TV to channel 3
or 4. Now set the CH3/CH4 switch on the
back of the VCR to match the channel se-
lected on the TV.
3
Turn on the VCR
Press the POWER button to turn on the VCR. Both the
"PWR." indicator and the "VCR" indicator on the dis-
play come on.
4
Select "ENGLISH" or "ESPAÑOL"
Select "ENGLISH" or
"ESPAÑOL"=Spanish by using
the PLAY/
▲
or STOP/
▼
button.
Then, press the F.FWD/
B
but-
ton.
Note: This function effects only the language on the
screen menu and not the audio source.
5
Begin channel preset
Press the F.FWD/
B
button once.
The tuner scans and memorizes
all active channels in your area.
●
The VCR distinguishes between standard TV chan-
nels and cable channels.
6
After scanning
The tuner stops on the lowest
memorized channel. The TV
screen returns to TV mode.
●
If "AUTO SET UP" appears on the TV screen again,
check the cable connections. Press the F.FWD/
B
button once again and the VCR will begin preset
again.
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using the CHAN-
NEL
▲
or
▼
button or directly pressing the number but-
tons on the remote control.
Note for using the number buttons:
●
When selecting cable channels which are higher than
99, press the +100 button first, then press the last two
digits. (Example: to select channel 125, first press the
+100 button then press "2" and "5").
●
You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
CH3
CH4
[Back of
the VCR]
NOTES:
●
Channel memory programming is NOT needed
when you connected the VCR to a cable box or
satellite box as in "Basic connections" on page
18. In this case, select the VCR and TV to channel
3 or 4 the same channel as the CH3 or CH4 switch
on the back of the VCR. Then, the channel you
want to record or view may be selected at the cable
box or satellite box.
●
Follow the steps below once. Repeat it only if
there is a power failure or if the VCR is unplugged
for more than 30 seconds. (In these cases, the pro-
grammed channels are erased.)
●
You must follow the steps below before attempt-
ing to play or record a video tape. If you want to
play or record a video tape BEFORE program-
ming the tuner, you can cancel it by pressing the
RESET/EXIT button. To program the tuner again,
see "CHANNEL SET UP AGAIN" on page 21.
CH 01
LANGUAGE SELECT
——————————————————
B
ENGLISH [ON]
ESPAÑOL
CH 01
AUTO SET UP
1B14
H7942
- 19 -
EN
