background image

33

8

Unit-Output

LINE 

can be Mono or Stereo. When mono, only the tip signal on the 

line input is used for both left and right. When stereo, the tip signal 
is left and the ring signal is right.

VOL 

shows the volume of the LEVEL knob.

SUB 

selects a combination of the mix channels for the submix bus. 

Turn to select a source and click to switch it in or out of the submix. 
There are 5 different sources.
- Drums: kick, snare, hihat, toms, cymbals and percussion.
- Fx: effect.
- Line: line input.
- Wave: accompaniment wave file.
- Metr: accompaniment metronome.

This allows for example to make a mix for recording or PA with just 
the drums and effect while still having all channels to the phones. 
The channel volumes of the submix are the same as those for the 
mix and are set on the UNIT-MIX page.

OUT1.2 

selects which audio bus is routed to output 1 and 2. Either 

the Mix, Mix!, Sub, Sub! or 1+2! bus. Mix and Sub are controlled by 
the LEVEL knob, the other ones are at a fixed level.

PHONS 

selects which audio bus is routed to the headphones output. 

This can be the Mix, Sub, 1+2, 3+4, 5+6, 7+8 or 7+8! bus. The 
level is controlled by the LEVEL knob, except for the 7+8! bus 
selection which has a fixed level equal to the other line outputs.

Bus selections with an exclamation mark have a fixed output level, 
so be careful with the volume setting of the connected device.

Summary of Contents for DrumIt Five











































Reviews: