background image

15 

 

 

Remplacer la batterie par un type incorrect; 

 

Disposer d’une batterie dans le feu ou un four chaud, écraser mécaniquement ou couper 

la batterie; 

 

Disposer la batterie utilisée conformément à vos règlements locaux ou aux instructions du 

fabricant de la batterie. 

 Regulatory Compliance 

 

FCC Statements 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) this device may not cause harmful interference, and (2) this device must accept 

any interference received, including interference that may cause undesired operation. 

Caution: The user is cautioned that changes or modifications not expressly approved by the 

party responsible for compliance could void the user's authority to operate the equipment. 

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference when the equipment is operated in a commercial 

environment. This equipment generates, uses, and can radiate radio frequency energy and, if 

not installed and used in accordance with the instruction manual, may cause harmful 

interference to radio communications. Operation of this equipment in a residential area is likely 

to cause harmful interference in which case the user will be required to correct the interference 

at his own expense. 

 

LVD/EMC Directive 

This product complies with the European Low Voltage Directive 2014/35/EU 

and EMC Directive 2014/30/EU. 

WEEE Directive–2012/19/EU 

 

The product this manual refers to is covered by the Waste Electrical & 

Electronic Equipment (WEEE) Directive and must be disposed of in a 

responsible manner. 

 

Battery Directive-2013/56/EC 

Battery in the product complies with the European Battery Directive 

2013/56/EC. For proper recycling, return the battery to your supplier or to a 

designated collection point. 

Summary of Contents for 2MTHFR-2M


















Reviews: