background image

4

5

2VV.

 Creating innovative solutions for you and your business since 1995.

     

PLEASE NOTE!

• 

If the product was shipped at below 0°C temperatures, let it 

rest for at least 2 hours, without turning it on, so that its inner 

temperature can match the surroundings.

2. UNPACKING

2.1 CONTROL THE DELIVERY

    

PLEASE NOTE!

• 

Unpack the product upon delivery and control for damages. 

In case of damage, inform and file a report with the carrier.

• 

 Any  claims  that  have  not  been  filed  in  due  time,  will  be 

disregarded later.

• 

Check that you have received the model ordered. Shou-

ld the delivered model differ from the one ordered, do not 

unpack the unit and notify the supplier immediately.

• 

After unpacking, check that the product and the accessories 

are in good order. Contact the supplier in case of any doubt.

• 

Do not attempt to commission a damaged product.

• 

If the product is not unpacked upon delivery, it must be sto-

red in a dry room with a temperature range of 

+5 °C to +40 

°C.

• 

This product must not be used by persons (incl. minors) 

with mental or physical disabilities, or insufficient experien

-

ce or knowledge in the safe use thereof, unless they are 

supervised or instructed on how to use the product by a 

person responsible for their safety. 

• 

Do no let children play with the unit.

+5 

o

C

+40 

o

C

All the packing material is 

environmentally friendly and can be 

reused or recycled. Please, contribute 

actively to the protection of the 

environment and procure the regular 

disposal or recycling of packing 

materials.

2.2 UNPACKING THE UNIT

Regulator IC3-C-AC

Regulator IC3-S-AC

Regulator IC-C2-EC

Regulator IC3-S-EC

1

X

1

X

1

X

1

X

4

X

4

X

1

X

1

X

1

X

1

X

5

X

3

X

1

X

1

X

1

X

1

X

14

X

14

X

5

X

3

X

Summary of Contents for IC3-CONTROL






























Reviews: