2Wire MEMO2 WS.502 Manual Download | Manualshive

Page: 34 / 35

background image

Manual WS.502 v1.5

2-Wire Energy Monitor

33

RESET SUMMARIZED:

Pressing keys while running:
1.

Key 1: Upgrading Javascript and CSS.

2.

Key 2: Upgrading firmware Web server WS502

Pressing keys during startup voltage:
3.

Toets 1: clear full database, IP address reset,
login and password

4.

Key 2: Reset IP address and password.

FAULTY JAVASCRIPT/STYLE: TEST 1+TEST 2

If you discover errors on the website, or there is no
key that responds, even after 'refresh page', an error
may have crept in when loading the script/style. There
are a few ways to download the javascript and
possibly the firmware again:

1.

Via the Login page

2.

Manually using the push buttons on the web
server

3.

Remote via an http statement

VIA THE LOGIN PAGE

With the "SCRIPT REPAIR" button on the login page,
you can reload javascript from another location.

MANUALLY USING THE PUSH BUTTONS ON THE WEB
SERVER

Re-download the java script from the 2-WIREserver by
pressing key 1 (left, shortest against the power
connector) and keep pressing until the left LED is
continuous. Only then release key. Now the LED
should stay on for 15 to 20 seconds and then go out
again.

Key 2

:If this is okay, then you do the same thing with

the right push button (key 2): keep pressing until the
flash stops and both LEDs are constantly burning, then
release key.

Now the LEDs also have to light 15 to 20 sec and then
the right LED starts flashing very quickly. After that,
the LED will burn continuously for about 3 seconds
and then go out. Everything okay !!!

When these things happen as described, try refresh
page again and log in.

REMOTE VIA AN HTTP STATEMENT

If you only have remote access to the web server, you
can use the following http instructions TO remotely
execute KEY1 (upgrade css/javascript) and KEY 2
(memo2 firmware upgrade).

Method:

Step 1:Ask for an access: enter your own

IP address

+

login

+

password

to get an XP key

ask XP key:
http://

192.168.0.123:8080

/

adminIP

?

XP

2015

&

antw: |4|13|

5|4

|0|

54 = XP-key

Step 2: Order upgrade css (KEY1):

req upgr FW CSS & script:

http://

192.168.0.123:8080

/

adminIP

?

XP

54

&DLFwStyleScript&

antw na ca 10sec: _30/06
9:26_|0|18|84|20.6.28.1|&#9745|0 = FW css
& script FW 20.6.28.1

Step 3: Order firmware upgrade (KEY2):

req upgrading FW server:

http://192.168.0.123:8080/adminIP?XP54&DL
FwWeb&

antw na ca 10sec: _30/06
9:26_|0|19|84|20.6.29.4|&#9745| START
UPGRADING|0 (FW 20.6.29.4)

Afterwards in toolbar get rid of instructions, reload
page and log in normally!

CLEAR FULL DATABASE, RESET IP ADDRESS AND
PASSWORD: KEY 1

Key 1 (shortest against power connector):

Procedure: Turn off

voltage of the WS502, wait 5

seconds, hold down key 1, turn on voltage, and keep
pressing until the LED starts flashing. Keep pressing
for another 3 seconds until the LED stops blinking and
then release the key.

«
...
32
33
34
35
»

Summary of Contents for MEMO2 WS.502




































Reviews:

No comments

Related manuals for MEMO2 WS.502

Brand: Zenith Pages: 218

SEH InterCon PS54a-G

Brand: SEH Pages: 24

Modbus Server-Cerberus ISO1745

Brand: IntesisBox Pages: 5

SUPERSERVER 6035B-8R+

Brand: Supero Pages: 110

Brand: Yawarra Pages: 4

NET-SERV Series

Brand: Panduit Pages: 24

Brand: ICP DAS USA Pages: 26

Brand: Planet Pages: 93

Boot Optimized Server Storage-S1

Brand: Dell EMC Pages: 32

m330 media server

Brand: Wadia Pages: 24

Brand: Symetrix Pages: 4

Brand: Silicon Graphics Pages: 30

Brand: Inspur Pages: 2

Brand: CTC Union Pages: 40

Yingxin NF5280M2

Brand: Inspur Pages: 64

Brand: Gateway Pages: 146

Brand: Gigabyte Pages: 102

301160U - 1TB Ethernet Disk RAID Network Attached...

Brand: LaCie Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands