3Com CoreBuilder 3500 Implementation Manual Download | Manualshive

Page: 230 / 592

background image

230

C

HAPTER

10: P

ACKET

F

ILTERING

pushSPGM

1 byte

Pushes the source port group mask (SPGM) onto the
top of the stack. The SPGM is a bitmap representing
the groups to which the source port of a packet
belongs. This instruction pushes 4 bytes on to the
stack.

Each port group mask is represented by a single bit in
the SPGM bitmap. Port group masks are assigned to
the bitmap in sequence, starting with port group mask
1 as the least significant bit through port group mask
32 as the most significant bit.

Use

pushSPGM

to filter by port groups. See “Using

Port Groups in Custom Packet Filters” for more
information.

pushDPGM

1 byte

Pushes the destination port group mask (DPGM) onto
the top of the stack. The DPGM is a bitmap
representing the groups to which the destination port
of a packet belongs. Pushes 4 bytes on to the stack.

Each port group mask is represented by a single bit in
the DPGM bitmap. Port group masks are assigned to
the bitmap in sequence, starting with port group mask
1 as the least significant bit through port group mask
32 as the most significant bit.

Use

pushDPGM

to filter by port groups. See “Using

Port Groups in Custom Packet Filters” for more
information.

eq (equal)

1 byte

Pops two values from the stack and compares them. If
they are equal, a byte containing the non-zero value is
pushed onto the stack; otherwise, a byte containing 0
is pushed. The contents of the stack determines the
size of the operands.

ne (not equal)

1 byte

Pops two values from the stack and compares them. If
they are not equal, a byte containing the non-zero
value is pushed onto the stack; otherwise, a byte
containing 0 is pushed. The size of the operands is
determined by the contents of the stack.

lt (less than)

1 byte

Pops two values from the stack and performs an
unsigned comparison. If the first is less than the
second, a byte containing the non-zero value is pushed
onto the stack; otherwise, a byte containing 0 is
pushed. The contents of the stack determine the size
of the operands.

Table 33

Packet Filtering Opcodes (continued)

Opcode

Memory
Requirements

Description

«
...
228
229
230
231
232
...
»

Summary of Contents for CoreBuilder 3500

















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CoreBuilder 3500

Galaxy S Blaze 4G

Brand: Samsung Pages: 4

Galaxy S Blaze 4G

Brand: Samsung Pages: 27

Galaxy S 4 mini

Brand: Samsung Pages: 26

GALAXY S GT-I9000

Brand: Samsung Pages: 132

Galaxy S Aviator

Brand: Samsung Pages: 56

Galaxy Note20 Ultra 5G

Brand: Samsung Pages: 2

Galaxy Note20 5G

Brand: Samsung Pages: 2

Brand: Samsung Pages: 41

Brand: Samsung Pages: 2

Brand: Samsung Pages: 28

Brand: Samsung Pages: 65

Brand: Samsung Pages: 7

Brand: Samsung Pages: 109

GALAXY Note 8.0

Brand: Samsung Pages: 51

Brand: Samsung Pages: 36

Brand: Samsung Pages: 68

Brand: Samsung Pages: 17

Brand: Wiko Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands