3Com CoreBuilder 9000 Command Reference Manual Download | Manualshive

Page: 41 / 784

background image

Entering Values

41

Entering Abbreviated Commands

You can abbreviate command strings by typing only as much of the
command as is necessary to make it unique:

Select a menu option: b po stpc

When you correctly enter either a full or an abbreviated command string,
you move to the last menu level or option that is specified in the string.
Information that is relevant to that option appears as a menu, a prompt,
or a display.

If you enter a command string incorrectly, the Administration Console
displays a message indicating that your entry was not valid or was
ambiguous. Reenter the command from the point at which it became
incorrect, or expand a truncated command until it becomes
unambiguous.

Entering Values

When you reach the level at which you perform a task, the
Administration Console prompts you for a value. The prompt usually
shows all valid values (if applicable) and typically suggests a default value.
The default may be the factory default value or the current value that you
have defined for that parameter.

The Administration Console displays the valid values in parentheses and
the default or current value in brackets. For example:

Enter a new value (disabled,enabled) [enabled]:

To accept the default or current value, press Enter.

Entering Values in Command Strings

A command string can also contain the value of a command parameter. If
you enter a value at the end of a command string, the Administration
Console executes the task and the previous menu appears on the screen.

For example, to set the path cost to the root through a port, from the top
level of the Administration Console, enter:

bridge port stpcost 20

or

b po stpc 20

«
...
39
40
41
42
43
...
»

Summary of Contents for CoreBuilder 9000

















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CoreBuilder 9000

Brand: GearMo Pages: 6

Brand: IBM Pages: 78

Brand: Supermicro Pages: 85

Brand: Overland Storage Pages: 2

Draco vario 474 Series

Brand: Ihse Pages: 77

Brand: Otto Bock Pages: 20

Brand: Lets Go Aero Pages: 13

Brand: IEI Technology Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands