3Com OfficeConnect WX1200 Command Reference Manual Download | Manualshive

Page: 28 / 646

background image

28

C

HAPTER

1: U

SING

THE

C

OMMAND

-L

INE

I

NTERFACE

VLAN Globs

A VLAN glob is a method for matching one of a set of local rules on an
wireless LAN switch, known as the location policy, to one or more users.
MSS compares the VLAN glob, which can optionally contain wildcard
characters, against the VLAN-Name attribute returned by AAA, to
determine whether to apply the rule.

To match all VLANs, use the double-asterisk (

**

) wildcard characters with

no delimiters. To match any number of characters up to, but not
including, a delimiter character in the glob, use the single-asterisk (

*

)

wildcard. Valid VLAN glob delimiter characters are the

at

(@) sign and the

period (.).

For example, the VLAN glob

bldg4.*

matches

bldg4.security

and

bldg4.hr

and all other VLAN names with

bldg4.

at the beginning.

Matching Order for Globs

In general, the order in which you enter AAA commands determines the
order in which MSS matches the user, MAC address, or VLAN to a glob.
To verify the order, view the output of the

display aaa

or

display config

command. MSS checks globs that appear higher in the list before items
lower in the list and uses the first successful match.

Port Lists

The physical Ethernet ports on a WX switch can be set for connection to
MAP access points, authenticated wired users, or the network backbone.
You can include a single port or multiple ports in one MSS CLI command
by using the appropriate list format.

The ports on a WX switch are numbered 1 through 4 (for the 3Com
Wireless LAN Controller WX4400) and 1 through 8 (for the 3Com
Wireless Lan Switch WX1200). No port 0 exists on the WX switch. You
can include a single port or multiple ports in a command that includes

port

port-list.

Use one of the following formats for

port-list

:

A single port number. For example:

WX1200#

set port enable 6

A comma-separated list of port numbers, with no spaces. For
example:

WX1200#

display port poe 1,2,4

«
...
26
27
28
29
30
...
»

Summary of Contents for OfficeConnect WX1200







































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for OfficeConnect WX1200

Brand: IDEC Pages: 8

Brand: IDEM SAFETY SWITCHES Pages: 2

Brand: Perel Pages: 4

Infinity IES-1881

Brand: LevelOne Pages: 2

Brand: Clas Ohlson Pages: 5

Brand: Cabletron Systems Pages: 194

Brand: UniFi Pages: 8

Elinx EIR418-2SFP-T

Brand: B&B Electronics Pages: 25

Brand: CIS Pages: 3

Brand: Key Digital Pages: 20

Brand: ATEN Pages: 26

Brand: Jerguson Pages: 16

SICOM3432G Series

Brand: KYLAND Pages: 29

Brand: SMC Networks Pages: 2

Brand: Accton Technology Pages: 8

Brand: Lindy Pages: 6

ControlZAPP CZ CEFL 10VDC

Brand: DANLERS Pages: 2

QSW-M2108 Series

Brand: QNAP Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands