3D Systems Cube 3rd Generation Quick Start Manual Download | Manualshive

Page: 3 / 36

background image

Congratulations on the purchase of your new Cube® 3D Printer! This Quick Start Guide has the use and

safety information you need to get started. Welcome to the 3D creative revolution – let the possibilities

begin!
If you have any questions, do not hesitate to reach us at cubifysupport@cubify.com.
This Quick Start Guide will give you basic instructions on how to get your Cube

®

3D Printer connected to

power and printing so you can start making your own creations.

For more detailed instructions, refer to the Cube

®

User Guide located on your USB

mass storage device.

SAFETY ........................................................................................................................ 1
YOUR CUBE AT A GLANCE ........................................................................................ 2

Operating Environment ..............................................................................................................2

UNPACK YOUR CUBE ................................................................................................. 3

What’s Included ..........................................................................................................................6

SETTING UP AND ACTIVATING YOUR CUBE ........................................................... 7
FINISHING YOUR CREATION ................................................................................... 24

Removing your Creation from the Print Pad ..........................................................................24
Removing Rafts ........................................................................................................................24
Removing Sidewalks ................................................................................................................25
Removing Supports .................................................................................................................25

MAINTENANCE .......................................................................................................... 26

Print Pad Maintenance .............................................................................................................26

Gap Verification

........................................................................................................................28

Manual Gap Adjustment ..........................................................................................................30
Recover A Cartridge .................................................................................................................31

«
1
2
3
4
5
...
»

Summary of Contents for Cube 3rd Generation





































Reviews:

No comments

Related manuals for Cube 3rd Generation

Brand: 3D Systems Pages: 17

Brand: 3D Systems Pages: 8

Brand: 3D Printing Systems Pages: 54

Brand: Mitsubishi Pages: 86

Phaser 6700V/DX

Brand: Xerox Pages: 162

Brand: WANHAO Pages: 18

ScreenWriter Colour ScreenWriter

Brand: Xante Pages: 446

Brand: Kashino Technology Pages: 72

Brand: Kyocera Pages: 28

10600 - Stylus Pro Color Inkjet Printer

Brand: Epson Pages: 8

1400 - Stylus Photo Color Inkjet Printer

Brand: Epson Pages: 8

10600 - Stylus Pro Color Inkjet Printer

Brand: Epson Pages: 183

Brand: Epson Pages: 279

1400 - Stylus Photo Color Inkjet Printer

Brand: Epson Pages: 4

Magicolor 2300 DL

Brand: Minolta Pages: 72

Brand: Digital Equipment Pages: 120

Brand: Digital Equipment Pages: 142

Brand: Digital Equipment Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands