background image

31

30

3DISON H700

 User Manual V.1

3DISON H700

 User Manual V.1

3DSION Metal Clay Printing

2. How to do a after-treatment for metal print-out : Firing method after 3D printing

  Sample should be processed in after-treatment process of drying and firing when metal 
paste is still in clay condition after being printed. Process for after-treatment depending on 
material is as follows;

1) Silver paste

  Take out printed clay with the tile and dry it for 24 hours by natural drying or dry it by 

warming for at least 1 hour using hair dryer or dry it by heating in the mini toaster oven for 
10 minutes in 200°C. Print-out which has been completely dried and cooled down can be 
detached from the tile easily.

NOTE : Be careful that print-out which is not completely dry, might be difficult  to get com-

plete firing and liable to crumble.

  Put the dried print-out in the electric kiln and set temperature at 780°C and fire it for 10 

minutes. Then silver clay changes into fine silver. Switch off the kiln and open the door to 
cool down the heat enough before taking the print-out out of the kiln.

NOTE : Mini electric kiln which ROKIT Inc. provides or any electric kiln which can be heated 

up to 980°C  can be used but quality of fired output may vary depending on the kiln. 

NOTE : Use tongs or wear gloves when take the sample out of the kiln to avoid scald.

③ 

 As the surface of the print-out taken out of the kiln has binder powder on it, brush off 

the surface using stainless steel brush provided in the kit box and silvery product will be 
completed.

NOTE : Brush thoroughly every corner for completion.

Annex1. Exchanging the Extruder for the Metal Clay Printing 

3DSION Metal Clay Printing

2) Copper/Bronze/Steel paste

  Take out output clay with the tile and dry it for 24 hours by natural drying or dry it by 

warming for at least 1 hour using a dryer. Print-out has been completely dried can be 
detached from the tile easily.

② 

 Prepare firing for dried sample using cube and carbon which are optional items. Build 

up about 3cm of carbon on the cube and put the sample on it and bury the sample entirely 
by pouring carbon on the sample as much as possible and then close the cover.

<Comparison of set temperature and firing time by material>  

 

Copper 

Bronze 

Steel

③ Upon completion of firing, switch off the kiln and open the door to cool down the heat 
enough. If the heat cools down to room temperature, finish work by taking the sample out 
of the cube and brushing the sample using stainless steel brush.

NOTE : Cube and carbon are recyclable (only the part which has not changed into white 

ash by oxidation). 

※ 

TIP

Be careful of scald when use toast oven or kiln and especially, in case the output has been 

fired in kiln, cool the output enough by opening the door at least an hour before take the 

printed object out of the kiln.

When you print in the tile after dry in toast oven, the output will not be separated easily unless 

you cool it enough so cool it for at least 30 minutes before you separate the output and then 

put it on wire mesh and put in the kiln.

Set temperature: 980°C

Firing time: 4 hours total

Set temperature: 

130°C>>843°C  

Firing time: 9 hours total 

After set at 130°C,

 increase by 130°C per an 

hour up to 843°C. I.E. 

130°C>260°C>390°

C>520°C>650°C>780°C>843°C

Set temperature: 

778°>>990°C

Firing time: 1 hour in 778°C, 

additional  firing in 990°C for

2 hours

Annex1. Exchanging the Extruder for the Metal Clay Printing 

Summary of Contents for H700






















Reviews: