background image

1

CONTENTS

Your 3DR Quad Kit contains:

Metal nuts (16)

Nylon nuts (4)

5 mm nylon bolts (8)

5 mm steel bolts (24)

25 mm steel bolts (12)

30 mm steel bolts (4)

Zip ties (8)

18 mm threaded spacers (12)

Accessory 

plate

APM plate

Top plate

Landing gear 

pieces (8)

You will also need:

Black arm (3)

Blue arm (2)

Battery strap

850 Kv motors with 

bullet connectors (4)

Option: 880 Kv motors

10 x 4.7 SF (normal) propellers (2)

Option: 11 x 4.7 SF propellers

10 x 4.7 SFP (pusher) propellers (2)

Option: 11 x 4.7 SFP propellers

Electronic speed 

controllers (4)

Power distribution board

Deans to XT60 adapter

Power module with Deans or 

XT60 connectors

Deans connectors - male (4)

6-position power 

module cable

 

»

Phillips screwdriver (small)

 

»

5.5 mm (7/32) wrench

 

»

Double-sided foam mounting tape

These instructions require some minor 

soldering. If you’re unfamiliar with 

soldering, our friends at Sparkfun have 

some great tutorials that can get you 

started, including this comic: 

learn.sparkfun.com/curriculum/42

.  

For an example of exactly what you’ll 

be doing for this assembly (soldering 

Deans connectors to ESCs), check out 

this video: 

youtu.be/3LJIQeKuLLU

.

Heat shrink tubing

Bottom plate

 

»

2 mm (5/64) hex wrench

 

»

Soldering equipment

 

»

Blue threadlocking compound

30 mm threaded spacers (4)

8 mm threaded spacers (4)

Metal lock washers (8)

Rubber washers (4)

Two-wire RC receiver cable

Five-wire RC receiver cable

XT60 connector - 

male

Summary of Contents for Quad DIY Kit









Reviews: