background image

1

Accessory 

plate (2)

APM plate

Top plate

Bottom plate

30 mm threaded spacers (4)

CONTENTS

Your 3DR Quad Frame 

Kit contains:

Metal nuts (16)

Nylon nuts (4)

5 mm nylon bolts (8)

5 mm steel bolts (24)

25 mm steel bolts (12)

30 mm steel bolts (4)

Zip ties (8)

18 mm threaded spacers (12)

Landing gear 

pieces (8)

Black arm (3)

Blue arm (2)

Battery strap

Power distribution board

Deans to XT60 adapter

Deans connectors - male (4)

These instructions require some minor 

soldering. If you’re unfamiliar with 

soldering, our friends at Sparkfun have 

some great tutorials that can get you 

started, including this comic: 

learn.sparkfun.com/curriculum/42

.  

For an example of exactly what you’ll 

be doing for this assembly (soldering 

Deans connectors to ESCs), check out 

this video: 

youtu.be/3LJIQeKuLLU

.

Heat shrink tubing

8 mm threaded spacers (4)

Metal lock washers (8)

Rubber washers (4)

Two-wire RC receiver cable

Five-wire RC receiver cable

XT60 connector - male

You will also need:

 

»

Phillips screwdriver (small)

 

»

5.5 mm (7/32) wrench

 

»

2 mm (5/64) hex wrench

 

»

Blue threadlocking compound

These instructions show the complete assembly and wiring process for a 3DR Quad 

using 3DR electronics. For assembling your Quad Frame Kit using other electronic 

components, please adjust these instructions accordingly.

Frame:

Electronics:

 

»

Double-sided foam mounting tape

 

»

Soldering equipment

Summary of Contents for Quad Frame Kit













Reviews: