background image

9

Mission Planner: Flight Data Screen

Before flying, complete Mission 

Planner’s configuration utilities, 

including RC (shown below), 

compass, accelerometer, frame 

type, and flight mode calibrations.

Visit 

planner.ardupilot.com

 for 

complete Mission Planner 

instructions.

CALIBRATION

Connect APM to your computer using the provided micro-USB cable. 

Windows will automatically install the correct drivers for APM.

APM USB port

Connect APM to Mission Planner:
1  Select Arduino Mega.
2  Select 115200.
3  Select Connect.

1

2

3

Mission Planner’s mandatory hardware calibration steps allow you to 

program and configure the APM autopilot for your copter.

Now you can connect APM to Mission Planner.

Select 

Initial Setup

Install Firmware

, and 

Quad

 to install flight code firmware onto APM.

On the left side of the Initial Setup screen, select 

Mandatory Hardware

.

 

You will need to 

perform each of the calibration procedures listed under this menu.

Frame Type

: Select your configuration: Plus or X (cross).

Compass

: Select the options to enable the compass, to allow automatic declination, and 

to select your autopilot type. Select

 Live Calibration

 to launch the wizard, and follow the 

prompts.

Accel Calibration

: Check the box for 

AC 3.0+

, select 

Calibrate

, and follow the prompts to 

calibrate the autopilot’s accelerometer. Make sure to wait a couple of seconds before and 

after changing the positions of the copter.

Summary of Contents for Y6













Reviews: