background image

3. Assemble Back 

The four corner connectors are mirror images 
of the front.  

On each side are “mid panel corner 
connectors”, which are basically simple L-
shapes for added strength.

The large 60mm hole is either for the included fan by itself, an air filter (purchased 
separately)/fan combo, or it can be covered up by a plastic disk depending on how 
much air flow you want.

Note that the fan, either by itself or paired with a 
filter or vent is necessary to draw air over the power 
supply.

 

 This both heats up the air inside the 

enclosure AND cools down the power supply, 
which extends its life.  Only use the circular disk 
(not included) to cover up the hole if you have 
moved the power supply outside of the enclosure, 
or if you simply don’t care about power supply 
longevity.

Confirm the direction of the fan’s air filter by 
plugging it into a USB power supply before attaching to the filter and back of the 
enclosure.  

The fan should be oriented to pull air OUT of the enclosure. 

 Use the 

long screws included in the fan packet to attach the fan.  The length of the screws may 
change depending on the depth of this particular 
shipment of fans.

The U-shaped hole is for the cable grommet and 
holder.  This will allow you to remove the enclosure 
without having to unplug the cables!  

Copyright 2020 3DUPfitters LLC

9

Summary of Contents for Prusa i3 MK2



















Reviews: