background image

Appendix 1. Electrical Diagram

III. Limited Warranty

Limited Warranty: 

 3M Purification Inc. warrants this Product will be free 

from defects in material and manufacture for the following periods from 

the date of purchase. Twelve (12) year for the Product, except for the 

booster pump and electronics, which are warranted for two (2) years, and 

the replacement filter cartridge and membrane, which are warranted for 

one (1) year. This warranty does not cover failures resulting from abuse, 

misuse, alteration or damage not caused by 3M or failure to follow installa-

tion and use instructions. No warranty is given as to the service life of any 

filter cartridges or membrane as it will vary with local water conditions and 

water consumption. 

3M MAKES NO OTHER WARRANTIES OR CONDI-

TIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, 

ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR 

FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY 

OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOMER 

OR USAGE OF TRADE.

  If the Product fails to satisfy this Limited Warranty 

during the warranty period, 3M will replace the Product or refund your 

Product purchase price.   This warranty does not cover labor.  

The remedy 

stated in this paragraph is Customer’s sole remedy and 3M’s exclusive 

obligation.

    

This warranty gives you specific legal rights, and you may have other 

rights which may vary from state to state, or country to country.  For any 

warranty questions, please call 

855-3M-WATER (855-369-2837)

 or mail 

your request to: Warranty Claims, 3M Purification Inc., 400 Research 

Parkway, Meriden, CT 06450.  Proof of purchase (original sales receipt) 

must accompany the warranty claim, along with a complete description of 

the Product, model number and alleged defect.

Limitation of Liability:  

3M will not be liable for any loss or damage aris-

ing from this 3M product, whether direct, indirect, special, incidental, or 

consequential, regardless of the legal theory asserted, including warranty, 

contract, negligence or strict liability.  Some states and countries do not 

allow the exclusion or limitation of incidental or consequential damages, so 

the above limitation or exclusion may not apply to you. 

 

  

3M is a trademark of 3M Company.

© 2014 3M Company.  All rights reserved.

34-8714-4683-6

3M Purification Inc.

400 Research Parkway

Meriden, CT 06450

855-3M-WATER (855-369-2837)

www.3MWater.com

Summary of Contents for 3MRO501













Reviews: