3M 5415A-IJ Instructions Manual Download

Page: 1 / 16

™

Cold Shrink Integrated Splice

Kit QS-III 5415A-IJ

for Jacketed Concentric Neutral (JCN) Cable
Instructions

IEEE Std. 404

15 kV Class

150 kV BIL

CAUTION

Working around energized systems may cause serious injury or death. Installation should

be performed by personnel familiar with good safety practice in handling electrical

equipment. De-energize and ground all electrical systems before installing product.

Kit Selection Table

Kit Number

Cable Insulation O.D. Range

Conductor Size Range

5415A-IJ

0.64" to 1.01"

(16,3 to 25,7 mm)

2 - 4/0 AWG*
(35–95 mm

)

* Splices (including size transitions) can be made to smaller or larger conductors (but larger conductors may require special neutral

handling), provided both cables are within the Insulation O.D. Range and the connector meets the dimensional requirements
shown below.

Connector Dimensional Requirements

Minimum Inches (mm)

Maximum Inches (mm)

Outside Diameter

0.40" (10,2 mm)

1.10" (28 mm)

Length

Aluminum (Al/Cu) Compression

—

4.50" (114 mm)

Length

Copper Compression and 3M

™

Shearbolt Connector

QCI 2-250

—

5.00" (127 mm)

September 2010

78-8127-8867-3-

Summary of Contents for 5415A-IJ

















Search results

Summary of Contents for 5415A-IJ

Reviews:

Related manuals for 5415A-IJ

Brands by name

Popular brands

3M 5415A-IJ, Instructions Manual

Search results

Summary of Contents for 5415A-IJ

Reviews:

Related manuals for 5415A-IJ

Brands by name

Popular brands