background image

Important Notice

 

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be relia-
ble, but the accuracy or completeness is not  guaranteed. Before using this product, you must evaluate it and determine if it is suit-
able for your intended application. You assume all risks and liability associated with such use. Any statements related to the prod-
uct which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have 

Communication Markets Division 
3M Telecommunications 

www.3M.com/Telecom

 

©3M 2016. All rights reserved.

 

Warranty; Limited Remedy; Limited Liability.

 

This product will be free from defects in material and manufacture for a period of 12 months from the time of purchase. 

3M MAKES 

NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FIT-
NESS FOR A PARTICULAR PURPOSE

. If this product is defective within the warranty period stated above, your exclusive 

remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. 

Except where 

prohibited  by  law,  3M  will  not  be  liable  for  any  loss  or  damage  arising  from  this  3M  product,  whether  indirect,  special, 

3M is a trademark of 3M Company

 

Summary of Contents for 8832-JG1 UPC SM
















Reviews: