background image

36

3M

 Digital Wall Display

© 3M 2005. All Rights Reserved.

E

N

G

L

IS

H

Maintenance

Maintenance

General Maintenance

For general cleaning of the screen and exterior of the 3M Digital Wall Display, use a damp cloth or dry cleaning 
cloth such as the 3M High Performance Cleaning Cloth.
Standard dry-erase cleaners may be used on the dry-erasable screens, such as Sanford

®

  Expo

®

 Whiteboard 

Cleaner. Do not use other spray cleaners or solvents on any part of the 3M Digital Wall Display.

Lamp Usage

Use and Replacement of Lamp

The 3M Digital Wall Display lamp has a normal operating time of approximately 1600 hours, called the lamp 
life. After the lamp has been operating for 1400 hours or longer, the following messages will appear on the 
screen for the first three minutes of operation. When this happens, turn off the 3M Digital Wall Display and 
replace the lamp with a new one. Using an old lamp in the 3M Digital Wall Display could cause a malfunction.

Onscreen Lamp Messages

PLEASE CHANGE THE LAMP

The lamp has been in use for 1400–1499 hours and needs to be changed. After replacing the lamp, reset the lamp 
timer.

THERE ARE (x) HOURS OF LAMP LIFE REMAINING 
THE Wall Display WILL SHUT OFF IN 40 MINUTES

The lamp has been in use for 1500–1579 hours, and the power will turn off after 40 more minutes. After 
replacing the lamp, reset the lamp timer.

THERE ARE (x) HOURS OF LAMP LIFE REMAINING 
THE Wall Display WILL SHUT OFF IN 5 MINUTES

The lamp has been in use for more than 1580 hours, and the power will automatically turn off after 5 minutes. 
After replacing the lamp, reset the lamp timer. 

All of these messages will display for no longer than three minutes, but each will display whenever you turn the 
lamp on again, until the lamp is replaced.

For lamp-changing instructions, please refer to the next page.

Summary of Contents for 9200IC Plus

























































Reviews: