3M Crimplok 6700-50 Instructions Manual Download

Page: 15 / 18

78-0013-1746-6-E

5.7

Remove the lapping film. Inspect the lapping film for fiber tracks. If the film has tracks, dispose of it. If not, restart

at step 5.1.

APC

UPC

5.8

Dry the connector using a new lint-free wipe. Do not

use the same wipe used for stripping fiber. Fold the

wipe to provide cushion. For APC, tilt the connector

so the ferrule tip is in full contact with the wipe.

For UPC, hold the connector perpendicular to the

wipe. Press the ferrule tip into the wipe slightly

and move the tip in a circular motion. After the

connector has been dried, add 1 or 2 drops of alcohol

or cleaning fluid to a clean area of the wipe. Do not

mix water and alcohol or water and cleaning fluid

on the wipe. If too much alcohol or cleaning fluid

soaks the wipe, just use the edge of the wetted area.

Clean the connector by moving the tip in a small

circular motion. Then dry the connector with a spot

on the wipe that has not been used yet, and is not

contaminated with water, alcohol or cleaning fluid.

Use a small circular motion. Finish with a twisting

motion.

1. Dry off water

2. Clean with alcohol or

cleaning ﬂ uid

3. Dry off alcohol or

cleaning ﬂ uid & twist.

Summary of Contents for Crimplok 6700-50



















Search results

Summary of Contents for Crimplok 6700-50

Reviews:

Related manuals for Crimplok 6700-50

Brands by name

Popular brands

3M Crimplok 6700-50, Instructions Manual

Search results

Summary of Contents for Crimplok 6700-50

Reviews:

Related manuals for Crimplok 6700-50

Brands by name

Popular brands