background image

3M Architectural Markets
3M U.S.

3M Center
Building 220­7W­07
St. Paul, MN 55144­1000
1­888­650­3497
3MArchitecturalMarkets.com

3M Canada

1840 Oxford St E
London, ON N5V 3R6
1-800-265-1840

3M  is  a  trademark  of  3M  Company.  Used  under
license in Canada. © 3M 2014. All rights reserved.
Please recycle
98-0406-0071-4

Installation Guide                                            LIGHTFALLS by 3M™ + Todd Bracher
                                                                                                                        Sconce

WARRANTY DOCUMENT

Product

LIGHTFALLS by 3M™ + Todd Bracher (the “Product”) is a decorative LED lighting system for dry interior use (the “Application”).

Limited Warranty

1. When used in the Application, 3M warrants to the party who purchased the Product directly from 3M (the “Buyer”) that the Product will be free from

defects in material and workmanship (the “3M Warranty”) for the applicable time period stated below (“Warranty Period”), which will begin on the
earlier of: (a) Product installation date; or (b) three months after 3M’s Product shipment date:

1.1

For all but a Product’s LED driver component, the Warranty Period is five years.

1.2

For a Product’s LED driver component, the Warranty Period is three years.

2. For Buyer’s convenience, 3M may provide a Specification Sheet, other engineering or technical information, recommendations, installation 

instructions, and other Product-related information or materials (all collectively referred to as “Product Information”), but 3M does not warrant any 
Product Information.

3. The 3M Warranty is contingent on the Product being stored, wired, installed, maintained, and used only as 3M recommends in all Product Information 

and in this Warranty Document. Also, 3M has no obligation under the 3M Warranty as to Product that has been: (a) modified or altered in any manner; 
(b) damaged through contact with a person or thing, misuse, accident, vandalism, neglect, or other action by anyone other than 3M; (c) affected by 
environmental conditions, such as power fluctuations, improper LED driver, or activity by animals or insects; or (d) used not in compliance with all 
applicable standards and electrical codes.

4. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, THE 3M WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, RIGHTS OR 

CONDITIONS, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY, 
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE AND THOSE ARISING FROM A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. 
BUYER IS RESPONSIBLE FOR DETERMINING IF A PRODUCT IS SUITABLE FOR ITS PARTICULAR PURPOSE AND ITS INSTALLATION.

Limited Remedy

3M must receive any 3M Warranty claim in writing by the earlier of: (a) applicable Warranty Period’s expiration date; or (b) fourteen business days after 
Buyer’s discovery of that 3M Warranty claim. If the Product is proven not to have met the 3M Warranty during the applicable Warranty Period, then BUYER’S 
EXCLUSIVE REMEDY AND 3M’S SOLE OBLIGATION, WILL BE AT 3M’S OPTION, TO REPAIR OR REPLACE THAT PRODUCT QUANTITY OR REFUND THE APPLI-
CABLE PURCHASE PRICE.

Limitation of Liability

3M WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO BUYER FOR DIRECT (other than the Limited Remedy above), SPECIAL, INCIDENTAL, INDIRECT 
OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS) IN ANY WAY RELATED TO A PRODUCT, THIS WARRANTY DOCU-
MENT, OR PRODUCT INFORMATION, REGARDLESS OF THE LEGAL OR EQUITABLE THEORY ON WHICH SUCH DAMAGES ARE SOUGHT.

Effective November 2013

Summary of Contents for LIGHTFALLS










Reviews: