3M Litmann Quality 3100 Instructions Manual Download | Manualshive

Page: 16 / 16

background image

3M and Temflex are trademarks of 3M Company.

Scotch is a registered trademark of 3M Company.

Important Notice

All statements, technical information, and recommendations related to 3M’s products
are based on information believed to be reliable, but the accuracy or completeness is
not guaranteed.

Before using this product, you must evaluate it and determine if it is

suitable for your intended application.

You assume all risks and liability associated with

such use.

Any statements related to the product which are not contained in 3M’s current

publications, or any contrary statements contained on your purchase order shall have no
force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability.

This product will be free from defects in material and manufacture at the time of purchase.

3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE.

If this product is defective within the warranty period stated above, your

exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund
the purchase price of the 3M product.

Except where prohibited by law, 3M will not

be liable for any indirect, special, incidental or consequential loss or damage
arising from this 3M product, regardless of the legal theory asserted.

3

Electrical Markets Division

6801 River Place Blvd.

Austin, TX 78726-9000

800-245-3523

Fax 800-245-0329

www.3M.com/electrical

Please Recycle. Printed in USA.

© 3M 2009. All Rights Reserved.

78-8127-6830-3-C

«
...
14
15
16

Summary of Contents for Litmann Quality 3100

















Reviews:

No comments

Related manuals for Litmann Quality 3100

Brand: EBECO Pages: 8

Brand: Amphenol Pages: 2

60SMF-LSA Series

Brand: Schäfter+Kirchhoff Pages: 16

Mic Cable WMKPVC

Brand: Whirlwind Pages: 1

Brand: Philips Pages: 2

Coil Cord US2-P70054

Brand: Philips Pages: 2

Coil Cord US2-P70051

Brand: Philips Pages: 2

5 m SWV3304W/10

Brand: Philips Pages: 2

Brand: ELEKTRA Pages: 84

Brand: Philips Pages: 2

Brand: Covid Pages: 7

Y-Con Cover-20-TC

Brand: Yamaichi Electronics Pages: 2

Brand: Vanco Pages: 12

Evolution EVSP4K12 1x2

Brand: Vanco Pages: 16

Brand: Speaka Professional Pages: 4

Brand: Digitogo Pages: 7

Brand: Icy Box Pages: 12

Brand: AVGear Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands