3M Litmann Quality 3100 Instructions Manual Download

Page: 4 / 16

78-8127-6830-3-C

3.0 Replace Insulation

3.1

Apply one half-wrapped layer of 3M

™

Temflex

™

Vinyl Electrical Tape 1700P

from edge of taper to edge of taper.

Note: Scotch

Glass Cloth Tape 27 or Scotch

Glass Cloth Tape 69, while not

included, may be added and used at this time.

™

Temflex

™

Electrical Vinyl Tape 1700P

Figure 5

3.2

Apply highly-stretched half-lapped layers of Scotch

Linerless Rubber Splicing

Tape 130C (

tacky side DOWN

) over 1700P tape and up onto tapers. Build up

half-lapped layers of tape gradually going out on existing insulation ½" (13 mm)

past top of tapers. Tape should be wrapped to a thickness equal to or greater than

the original insulation.

Scotch

Linerless Rubber Splicing Tape 130C

Tacky Side DOWN

½" (13 mm)

past end of taper

½" (13 mm)
past end of taper

Figure 6

3.3

Starting ½" (13 mm) past end of 130C tape apply one half-lapped layer of

1700P tape over the 130C tape, extending ½" (13 mm) past the other end of the

130C tape.

™

Temflex

™

Vinyl Electrical Tape 1700P

½" (13 mm)

past end of

previous layer

½" (13 mm)
past end of
previous layer

Figure 7

Summary of Contents for Litmann Quality 3100

















Search results

Summary of Contents for Litmann Quality 3100

Reviews:

Related manuals for Litmann Quality 3100

Brands by name

Popular brands

3M Litmann Quality 3100, Instructions Manual

Search results

Summary of Contents for Litmann Quality 3100

Reviews:

Related manuals for Litmann Quality 3100

Brands by name

Popular brands