3M Litmann Quality 3100 Instructions Manual Download

Page: 7 / 16

78-8127-6830-3-C

5.4

Start 2" (50 mm) from Scotch

Linerless Rubber Splicing Tape 130C and apply

one half-lapped layer of Scotch

Heavy Duty Mining Tape 31 with mastic side

toward the cable continuing 2" (50 mm) past the end of the 130C tape. Always

wrap the 31 tape toward the machine end of the cable.

2" (50 mm)
past end of
previous layer

Scotch

Heavy Duty Mining Tape 31

(Mastic side toward cable)

Machine End

Start taping here

Figure 14

5.5

Starting 1" (25 mm) past the 31 tape, apply 3 half-lapped layers of

™

Temflex

™

Vinyl Electrical Tape 1700P to each end to temporarily secure

the ends of the 31 tape until the tape reaches full bond.

1"
(25 mm)

(25 mm)

™

Temflex

™

Vinyl Electrical Tape 1700P

Figure 15

Summary of Contents for Litmann Quality 3100

















Search results

Summary of Contents for Litmann Quality 3100

Reviews:

Related manuals for Litmann Quality 3100

Brands by name

Popular brands

3M Litmann Quality 3100, Instructions Manual

Search results

Summary of Contents for Litmann Quality 3100

Reviews:

Related manuals for Litmann Quality 3100

Brands by name

Popular brands