6
2:13 Set-up menu
(fig. 10)
To enter the set-up menu, have the headset in off mode and
press
(~2 seconds)
on both the PTT and on/off/mode button
on the right cup at the same time. Use the on/off/mode button
to navigate through the menu and the [+] and [–] buttons to
adjust the settings.
To exit the set-up menu, turn the headset off.
These are the options available in the set-up menu:
2:14 BCLO (Busy channel lock out)
This menu setting lets you change the way the headset
reacts when you try to transmit on a busy channel. There
are two options to choose from: “carrier” and “sub channel”
(code) with or without a warning tone. If you want the headset
to respond to the carrier wave, select the “carrier” option;
if you want it to react to the sub channel, choose the “sub
channel” option.
(“BCLO off” - “BCLO carrier” - “BCLO carrier
tone” - “BCLO sub channel” - “BCLO sub channel tone”)
Default: BCLO carrier tone.
2:15 Max transmission time
This function lets you adjust the maximum transmission time.
You can choose between
30 seconds
up to
5 minutes
and
off-mode. Each change is confirmed by a voice message.
(“OFF”, “30 s”, “1 min”, “2 min”, “3 min”, “4 min”, “5 min”)
Default: 3 min
2:16 Automatic power off
The automatic power off is the time that elapses before the
headset is automatically powered off if there is no activity
(button presses or VOX activation).
Before the headset powers off you will hear a voice message
and warning beeps. To abort the automatic power off function,
press any button.
(“OFF”, “30 min”, “60 min”, “2 h”, “4 h”, “8 h”)
Default: 4 h
2:17 Microphone input
This product is supplied and calibrated for use with a dynamic
microphone (MT73) as standard.
You can however adjust the microphone gain. The
microphone gain can be changed here. It is also possible
to switch off the microphone and just use the headset for
listening. Each change is confirmed by a voice message.
(“OFF”, “Low”, “Medium”, “High”)
Default:
Medium
2:18 External jack input sensitivity level control
Level control for incoming signal from external equipment
connected to the external jack.
Each change is confirmed by a voice message.
(“OFF”, “Low”, “Medium”, “High”)
Default: OFF
*2:19 Bluetooth
®
streaming
Enable or disable the streaming function.
Default: Enable
*2:20 Bluetooth
®
Multipoint
Enable or disable the Multipoint function.
Default: Enable
2:21 Reset to factory default
(fig. 11)
To confirm a reset to factory default, hold the plus button
for
two seconds
.
This is confirmed by the voice message
“Restored factory defaults”
3. CLEANING AND MAINTENANCE
Use a cloth wetted with soap and warm water to clean the
outer shells, headband and ear cushions.
NOTE: Do NOT immerse the hearing protector in water.
If the hearing protector gets wet from rain or sweat, turn the
earmuffs outwards, remove the ear cushions and foam liners,
and allow to dry before reassembly. The ear cushions and
foam liners may deteriorate with use and should be examined
at regular intervals for cracking or other damage. When used
regularly, 3M recommends replacing the foam liners and ear
cushions at least twice a year to maintain consistent
attenuation, hygiene, and comfort. If an ear cushion is
damaged, it should be replaced. See Spare Parts and
Accessories Section below.
3:1 Removing and replacing the ear cushions
D:1 To remove the ear cushion, slide your fingers under the
inside edge of the ear cushion and firmly pull straight out.
D:2 Remove existing liner(s) and insert new foam liner(s).
D:3 Fit one side of the ear cushion into the groove of the
earcup and then press on the opposite side until the ear
cushion snaps in place.
3:2 Use and storage conditions
Remove the batteries before storing the product. Do not store
the hearing protector at temperatures above 55 °C or 131 °F,
(for example on a dashboard, parcel shelf or window sill), or
at temperatures below –20 °C or –4 °F. Do not use the
hearing protector at temperatures above 55 °C or 131 °F, or
below 0 °C or 32 °F.
3:3 Spare parts and accessories
3M™ PELTOR™ HY83 Hygiene kit
Replaceable hygiene kit consisting of two attenuation
cushions, two foam rings and two snap-in ear cushions.
3M™ PELTOR™ HY80 Gel ring for industrial headset
Gel sealing rings featuring a super-thin polyurethane skin with
a double-hump top face design and a silicone gel-filled
bladder with a foam backing.
3M™ PELTOR™ HY100A Single-use protectors
A single-use protector that is easy to fit to the ear cushions.
Pack of 100 pairs.
EN
* Only WS
TM
(Bluetooth
®
) models
