background image

3M, Scotch, Scotchlok and SLiC are trademarks of 3M Company.

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, 
but the accuracy or completeness is not guaranteed.

 

Before using this product, you must evaluate it and determine if it is suitable for 

your intended application.

 

You assume all risks and liability associated with such use.

 

Any statements related to the product which are not 

contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless 
expressly agreed upon, in writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability. 

This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase.

 

3M MAKES NO 

OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A 
PARTICULAR PURPOSE.

 

If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, 

to replace or repair the 3M product or refund the purchase price of the 3M product.

 

Except where prohibited by law, 3M will not be 

liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the 
legal theory asserted. 

3

Communication Markets Division

6801 River Place Blvd.

Austin, TX 78726-9000

1-800-426-8688

www.3M.com/Telecom

Please Recycle. Printed in USA.

© 3M 2011. All Rights Reserved.

78-8135-7466-8-B

Summary of Contents for SLiC 530







Reviews: