background image

Important safety advice

Your printer has been built with user safety as main concern, yet it must NOT be used by individuals with reduced mental 
or physical abilities.

This printer is not a toy, is meant to be used by fully responsible and knowledgeable people and printing 
area must be kept locked in presence of children or people with serious mental problems.

Safety issues to be considered:

Risk of fire: don't turn on printer close to flammable substances. Don't use any flammable substance to

clean the machine inner parts. Do not use any spray product inside printer. Allow 
correct printer ventilation: don't obstruct air inlets and outlets, keeping them free from 
dust and other contaminants. 

Risk of toxic fumes: wrong temperature settings may cause toxic fumes emissions. Be sure to follow 

guidelines and settings from supplier of your filament. Use printer in a well vented 
room. If possible use machine smoke exhaust  port.

Electrocution: do not use in presence of condensing moisture and/or conductive dusts. Disconnect AC 

power cord before accessing inner parts. Do not attempt any maintenance work on 
electric or electromechanical parts. Promptly report any electrical malfunctioning 

Electromagnetic compliance: this is a class A product. In a domestic environment this product may 

cause radio interference in which case the user may be required to take adequate 
measures.

4

Summary of Contents for A4v3





















































Reviews: