background image

18

1 x Press 

Stop-button

1 x Press button 

P2 / Set Up

a

Hold down Up- + Down-button 

simultaneously

1 x Press button 

P2 / Set Up

1 x Press button 

P2 / Set Up

Pairing another handheld transmitter:

Beep from motor 

+ down and up

1 x Press button 

P2 / Set Up

+

Beep from motor 

+ down and up

+

+

The motor confirms 

the programming

with 3 beeps and 

down and up

OK

a

 

Handheld transmitter already paired

b

 

New handheld transmitter / not paired

a

b

or

+

The motor confirms 

the programming

with 7 beeps and 

down and up

OK

b

b

1 x Press P1 button

3 x Beep 

from motor 

Note: 

The endpoints must already be programmed  

to be able to use this method.

1 x Press button 

P2 / Set Up

Delete handheld transmitter:

Beep from motor 

+ down and up

1 x Press button 

P2 / Set Up

+

Beep from motor 

+ down and up

+

+

The motor confirms 

the programming

with 3 beeps and 

down and up

OK

a

 

b

 

Handheld transmitter already paired

b

 

Handheld transmitter to be deleted

a

b

1 x Press button 

P2 / Set Up

Delete all handheld transmitter:

Beep from motor 

+ down and up

1 x Press button 

P2 / Set Up

+

Beep from motor 

+ down and up

+

+

The motor confirms 

the programming

with 3 beeps and 

down and up

OK

a

 PROGRAMMING RADIO TRANSMITTER 

3T-MOTORS Radio tubular motors

  |  Programming radio transmitter

Summary of Contents for 3T-MOTORS 3T35-10RB

























Reviews: