background image

12

MOUNTING INSTRUCTIONS FOR 3T-MOTORS  MINI-TUBE MOTORS 

MOTOR TYPE 3T35-B

Use proper suspension springs:

 To fasten the roller shutter curtain to the roller shutter shaft, please be sure to use  

  suitable suspension springs for motor operation. These special mini suspension springs only protrude  
  approx. 1 mm into the shaft. This allows the shaft to rotate freely. When commercially 
  springs are used, there will be grinding marks on the motor housing because the suspension pin  
  protudes too far into the roller shutter shaft, which leads to damage and destruction of the motor. 
  In case of any kind of grinding marks on the motor housing, the warranty claim is void. 

 Mini suspension springs  

 Optional tubular motor accessories (page 18 – 19)

Use correct roller shutter shaft with external fold:

 

For steel shafts with a width across flats of 40 mm (SW40), only use shafts with 

  an external fold. Steel shafts with an internal fold will damage and destroy the motor.

Explanation:

 Avoid overstressing and resulting premature aging of the motor by using the correct suspension 

  springs and the correct roller shutter shaft with external fold!

 Keep in mind that the motor housing has a diameter of 35 mm and the roller shutter shaft SW40 

  has an outer diameter of 40 mm. When using commercially available springs or roller shutter shafts 
  with internal fold, the motor housing will be left with grinding marks, since the suspension pin or the 
  fold protrude too far into the roller shutter shaft. Contrary to its intended use, the motor runs 
  permanently against an overload and outside its characteristic data. 

 Matching roller shutter shafts SW40  

 Optional tubular motor accessories (page 18 – 19)

Mini Suspension spring

8-sided shaft SW40 
with external fold

Do not use 
8-sided shaft SW40 
with internal fold!

Suspension spring

 INSTALLATION INSTRUCTIONS

3T-MOTORS Tubular motors

  |  Installation instructions

Summary of Contents for 3T-MOTORS 3T45-10B





















Reviews: