background image

13

INSTALLATION AWNING MOTOR

1

 Preparation:

 Screw in awning & secure with straps or ropes.

 Remove awning from wall bracket & place on safe surface.

2

 Prepare motor for installation:

 

Slide limit switch adapter flush against motor head.  

>

 

fig. 2.1 / 2.2

 Secure the shaft adapter with the supplied securing bracket.  

>

 

fig. 2.3 / 2.4

3

 Installation awning motor:

 Remove the cover to access the side bearing (also awning bracket) 

  and fastening screws.  

>

 

fig. 3.1

 Loosen the screw that secures the side bearing to the support tube.  

>

 

fig. 3.2

 Remove all screws connecting the side bearing 

  and the crank mechanism.  

>

 

fig. 3.3

 Remove the side bearing from the support tube.  

>

 

fig. 3.4

 Remove the crank mechanism.  

>

 

fig. 3.5

Attention: 

 

Awning arms are under strong tension!

2.1

Limit switch adapter

Motor head

2.2

2.3

Securing bracket

2.4

Click

Shaft adapter

 Remove the shaft capsule from the shaft.  

>

 

fig. 3.6

    

If the shaft capsule is tight, use a hammer and screwdriver. 

  Be careful not to damage the shaft.

 

Push the awning motor with shaft adapter first into the shaft.  

>

 

fig. 3.7

 

Make sure motor head & limit switch adapter are flush in shaft.

 Screw the universal bearing onto the side bearing on the side 

  facing the awning shaft.  

>

 

fig. 3.8

3.7

3.8

Shaft & 

wound up 

Awning

 INSTALLATION INSTRUCTIONS

3T-MOTORS Tubular motors

  |  Installation instructions

Side bearing

Cover

3.1

Support tube

Side bearing

3.2

3.2

3.4

Crank mechanism

3.5

3.6

Support tube

Shaft capsule

Shaft & 

wound up 

Awning

Universal 

bearing

Summary of Contents for 3T-MOTORS 3T45-10B





















Reviews: