background image

3W 42i Engine Manual

more infos: www.3w-modellmotoren.de

Dear customer,

Thank you for placing your confidence in 3W. Our long experience (since 1985) in designing and

producing model airplane engines, ranging from single up to six cylinder, has been utilized to

provide you with the best engine possible. Our in-house engineer has been designing two and

four stroke engines for gasoline and diesel for 38 years. We are continually looking at new

technologies and working on new designs. Please be assured that we at 3W always strive to

provide you with engines that are state of the art.

You can count on your 3W engine to have:

• 

a high level of precision

• 

high torque in the low rpm range

• 

excellent running characteristics

 a long life

• 

lots of power

And a 36 month conditional warranty.

We wish you plenty of fun and success with your new 3W engine.

Sincerely,

The 3W Team

Limited Warranty

We grant a 36 month warranty from the date of purchase. This warranty is limited to the replacement

of defective parts that are a direct result of faulty material or manufacturing. No claim concerning

a defect caused by non-compliance with installation or operation instructions, mishandling, unsuitable

spare parts nor unskilled repairs will be acknowledged. Please ask your dealer to fill out a warranty

certificate for you at the time of purchase. Important: Keep this certificate in a safe place as this

warranty will not be honored without it. The original receipt is also required.

Warning!

This engine is not a toy! Serious injury and /or death can occur from its misuse! READ and become

familiar with this entire instruction manual. LEARN the engine's applications, limitations, and

possible hazards.

Summary of Contents for 42i



















Reviews: