background image

3W 85i Engine Manual

more infos: www.3w-modellmotoren.de

Important!

For your safety and for the safety of those around you -- also to learn what is required to maintain your warranty -

we strongly advise you to read this entire manual carefully BEFORE you start using the engine.

Safe Operation and 3W's Conditional Warranty

For safe operation and to maintain your warranty you must:

 Have a properly designed engine box on your model

 Mount the engine correctly

 Provide adequate air flow and cooling for the engine

 Provide adequate air flow and cooling for the exhaust

 Use an approved propeller and spinner

 Drill the propeller correctly

 Balance the propeller correctly

 Tighten the propeller bolts correctly and check them regularly

 Properly mount your ignition to avoid overheating

 Use the correct battery and regulator (if applicable) for your ignition

 Use the correct switch for your ignition

 Use an appropriate fuel tank, plumbing lines, and installation

 Use the appropriate fuel for break in and after break in (gas and oil)

 Insure adequate filtering of your fuel

 Maintain your engine properly, keeping it clean, etc.

 Use a pre-flight check list before flying your model

 Secure your model properly when starting

• 

Not use your fingers or hand to start your model

 Adjust your carburetor correctly

 Not adjust your carburetor while the engine is running

 Insure that your spark plug is in good condition and is secured correctly

 Insure that your ignition wires are not frayed and are protected

 Insure that your ignition cap is securely mounted

• 

Keep all people behind the line of the prop

 Do not put anything (i.e., fingers, body parts, objects, et al) into the rotating propeller

 Keep children away. All spectators should be kept a safe distance away from the running engine.

 Wear proper apparel. Do not wear loose clothing, gloves, neckties, jewelry, or neck straps for your radio

which may get caught in the moving propeller.

 Always wear eye protection when starting the engine.

 Do not operate this engine if you are under the influence of any drugs, alcohol or medication that could affect

your ability to use the engine properly.

Disclaimer

We cannot control how safely our products will be used. And, therefore we do not accept any  responsibility for

damage, or injury from their usage.

Summary of Contents for 85i B2


















Reviews: