background image

 Read

 

and Follow These Important Safety Instructions 

You will see 

Warning

 and 

Caution

 statements on the following Pages.  

Read and follow these safety instructions carefully. Failure to do so could result in serious personal injury or death. 
 

 

Warning

  

means that severe injury or death may result from failure to follow  instructions 

 

Caution

  

means that property damage or injury may result from failure to follow instructions 

• 

Be sure to read and follow all instructions carefully. 

• 

To reduce the risk of electric shock, this equipment has a grounding type plug, that has a third (grounding) pin. 
This  plug  will  only  fit  into  a  grounding  type  outlet.  If  the  Plug  does  not  fit  into  the  outlet,  contact  a  qualified 
electrician to install the proper outlet. Do not change the plug in any way. 

• 

Check  to  make  sure  the  garage  door  is  properly  installed  and  balanced. 

Garage  door  &  parts  are  under 

extreme  tension  and  under  no  circumstance  should  you  attempt  to  adjust  on  your  own

. Have a qualified 

garage door service person make repairs to cables, spring and other hardware before installing the opener. 

• 

Install  Entrapment  Warning  Label  next  to  control  button.  Read  the  Control  Adjustment  Warning  Label.  Install 
Emergency Release Tag to the Emergency Release Cord. Mount the Emergency Release Knob 180cm from the 
floor. Use the manual release only to disengage the trolley. Do not use the Red Release Cord and Knob to pull 
door up or down. If possible, use the Emergency Release only when the door is closed. 

• 

Do not connect opener to power source until instructed. Install door opener 210cm or more above floor. 

• 

After installing opener, the door must reverse when it comes in contact with a 5cm high object. Check this safety 
feature often. 

• 

REMOVE ALL ROPES CONNECTED TO THE GARAGE DOOR. 

• 

DISENGAGE ALL EXISTING GARAGE DOOR LOCKS TO AVOID DAMAGE TO THE GARAGE DOOR. 

• 

Fiberglass,  aluminum  and  steel  doors  must  be  reinforced  to  prevent  damage.  Consult  with  manufacturer  for 
recommendations. 

• 

All  installation  and  wiring  must  be  done  in  strict  compliance  with  local  and  state  building  and  electrical  codes. 
Connect the power cord to a properly grounded outlet only. Do not in any way alter or remove the grounding pin. 

Photo  Eye  System  must  be  installed  properly.  Operators  recommend  Photo  Eye  System  is  installed  on  every 
garage  door  for  your  added  protection.  Opening  doors  must  not  close  and  Closing  doors  must  open  once  the 
beam is broken.   See the test procedure page 16. 

• 

Locate push button within sight of garage door, away from all moving parts and out of reach of children (minimum 
150cm above floor). To reduce the risk of injury to persons, use this operator only with a sectional door. 

• 

Never operate the opener if the system is not operating properly. 

• 

Always disconnect electric power before making repairs or removing cover. 

• 

Activate opener only when the door is in full view and free from obstructions. 

• 

No one should enter or leave the garage while the door is moving. Do not allow children to play near, or operate 
the door. Keep the remote control away from children. 

• 

After Installation is complete fasten this manual near the garage door. Perform periodic safety checks and 
recommended maintenance and adjustments. 

• 

NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.  

• 

Test door opener monthly. The garage door MUST reverse on contact with a 5cm high object (or a two by 4 board 
laid flat) on the floor. After adjusting either the force or the limit of travel, retest the door opener. Failure to adjust 
the opener properly increases the risk of severe injury or death. 

• 

For products having an emergency release, when possible, use the emergency release only when the door is 
closed. Use caution when using this release with the door open. Weak or broken springs are capable of 
increasing the rate of door closure and increasing the risk of severe injury or death. 

• 

KEEP GARAGE DOORS PROPERLY BALANCED. See owner’s manual. An improperly balanced door increases 
the risk of severe injury or death. Have a qualified service person make repairs to cables, spring assemblies, and 
other hardware. 

• 

SAVE THESE INSTRUCTIONS. 

Summary of Contents for 4DS1























Reviews: