background image

SPECIFCATIONS

Motor: 12 Volt DC

Fuse: 45 Amp

Maximum re-start pressure: 90 psi

Maximum continuous operating time is 20 minutes

This air compressor is designed to run on a 12 Volt DC battery

MAINTENANCE AND CLEANING

 

We recommend that only qualified persons perform maintenance and 

servicing on the air compressor.

 

NOTE: Always unplug or shut down your compressor  before attempting 

any type of maintenance. Wait for compressor to cool before servicing.

Ensure the unit has been switched off and has cooled down completely 

before cleaning.

•  Never immurse this unit in water.

•   Simply wipe down with a soft cloth.

•   IF THE UNIT STOPS 
  DURING OPERATION

1.

  Check the battery condition. Low voltage can trip 

the circuit breaker or trigger the protection feature.

2.

 Check the circuit breaker, reset if necessary.

3.

 The unit is equipped with an automatic protection 

device. In the event the unit reaches an unsafe 

operating temperature, a protection circuit will cut 

power to prevent damage to the unit. If the 

protection circuit activates, immediately disconnect 

the unit from the power source and allow it to cool.

TROUBLESHOOTING

   CAUTION

•  Small items will inflate quickly and can easily be damaged. Pay  

  special attention to bicycle tyres. They inflate very fast and can  

  rupture. Be prepared to stop the unit quickly when manufacturer’s  

  recommended inflation pressure is reached.

•  Use this compressor with 12 Volt DC systems only.

•  Keep the vehicle engine running while the compressor is working.

9

Summary of Contents for 150L













Reviews: