background image

Pag 3 | 13   

www.6tlengineering.com

   18/06/2022   YAV90132 / YAV90133   

 
 

 

1. 

SAFETY GUIDELINES 

 

Caution  

Read this manual carefully to understand the contents well and make the proper use of 

this system accordingly. 

Keep the manual safely for ready reference at any time. For basic operation of the system/module, 
also read the relevant manuals carefully to understand the contents well, and then make the proper 
use of this system accordingly. 

Note  

Only qualified and entitled  personnel are authorized to carry out operations of installation 

and routine on the devices described in this manual. The company installing it would bear 
responsibility for any security or operating failure of the lift, when such failure is due to the 
parameters incorrect programming. 

The product described in this manual can be configured to comply with the ruling of different 
countries. The manufacturer does not hold any responsibility if the company installing it does not 
configure it according to the legal, commercial or security prescriptions that may be in force in the 
place of installation or otherwise agreed with the customer. 

 

2. 

ELECTROMAGNETIC COMPATIBILITY GUIDELINES 

 

The product YAV90132 / YAV90133 to which this manual relates meet the provisions of the EU Directives 
2014/30/CE which declares the compliance of electromagnetic compatibility (EMC) and directive 
2014/35/CE of low voltages electronic devices. 

For accessories or other elements that can be connected to this product, see their corresponding 
Declaration of Conformities 

 

 

 

 

 

 

Summary of Contents for YAV90132














Reviews: