background image

150Mbps  Wireless  Broadband  Router 

User  Manual 

 

NATIONAL RESTRICTIONS 

 

 

 

CE Mark Warning 

 

This is a class B product. In a domestic environment, this product may cause radio interference, in which 

case the user may be required to take adequate measures. 

 

Frequency range - 2400.0 - 2483.5 MHz 

 

Country

 

Country

 

Reason/remark

 

Bulgaria 

none 

General  authorization  required  for  outdoor  use  and 

public service. 

France 

Outdoor  use  limited  to  10 

mW  e.i.r.p.  within  the  band 

2454-2483.5 MHz 

Military  Radiolocation  use.  Refarming  of  the  2.4 

GHz band has been ongoing in recent years to allow 

current  relaxed  regulation.  Full  implementation 

planned 2012. 

Italy 

none 

If  used  outside  of  own  premises,  general 

authorization is required. 

Luxembourg   

none 

General  authorization  required  for  network  and 

service supply (not for spectrum). 

Norway 

Implemented 

This subsection does not apply for the geographical 

area  within  a  radius  of  20  km  from  the  centre  of 

Ny-Ålesund. 

Russian 

Federation 

none 

Only for indoor applications. 

 

Note: Please don’t use the product outdoors in France.

 

Summary of Contents for SMART WRT-150






























































Reviews: