background image

4

•    When outdoors observe wind direction. When working indoors 

ensure that there is sufficient ventilation.

•   Do not spray at the device.

•    The device only splash-proof when the air hose is correctly 

connected.

•    Do not let children play with the device. Keep out of reach of 

children.

•    Care must be taken that the mains cable is not damaged. 

If damage is observed bake immediately to an authorized 

customer service centre to be changed.

•    Remove mains plug from socket when not in use 

•    Repairs to electrical parts should only be carried out at an 

authorized customer service centre.

•   Do not use spray guns to spray flammable liquids.

•   Do not clean spray guns with flammable solvents.

•    Take precautionary measures against potential hazards from 

spray liquid and follow any instructions given on containers  

or laid down by the manufacturer of liquid.

•   Do not spray any liquids of unknown hazard potential.

•   Keep work area clean and will lit.

•   Forbidden to spray to the hatch of the motor and etc.

•    When spraying normally, the motor  

should not be under the head of  

the gun and the container.

12

10

8

8

13

Know your product

1. On/Off Switch
2. Carry Handle
3. Spray Gun
4. Spray Gun trigger
5. Paint Volume Control Collar
6. Air Filter Cover
7. Air Cap
8. Nozzle 
9. Air Cap Nut
10. Paint Pot

11.  Paint Pot Lid  

(additional pot only)

12.  Viscosity Cup 
13.  Nozzle Cleaner/ 

Cleaning Needle

14. Suction Tube
15. Hose
16. Spray Gun Hose Inlet port
17. Paint Sprayer Hose outlet port
18. Spray Gun Hanging Hook
19. Air Cap ears

1

2

17

19

4

11

10

6

9

8

7

3 18

5

15

16

14

Summary of Contents for 909450P









Reviews: