background image

10

Risk of hot surfaces

Hazard

What could happen

How to prevent it

Contact with hot engine and 

generator components.

Contact with hot surfaces, such as 

engines exhaust components, could 

result in serious burns.

During operation, touch only the 

control surfaces of the generator. Keep 

children away from the generator at 

all times. They may not be able to 

recognize the hazards of this product.

Risk of moving parts

Hazard

What could happen

How to prevent it

Contact with moving parts can 

result in serious injury.

The generator contains parts which 

rotate at high speed during operation. 

These parts are covered by guarding to 

prevent injury.

Never operate generator with guarding 

or cover plates removed. Avoid wearing 

loose fitting clothing or jewellery which 

could be caught by moving parts.

Risk from lifting

Hazard

What could happen

How to prevent it

Lifting a very heavy object.

Serious injury can result from 

attempting to lift too heavy an object.

When lifting, always keep the object 

you are lifting near the vertical axis of 

your body. DO NOT use you back to 

lift heavy loads. Both people should 

crouch down, grab the underside 

of unit and use your legs to carry 

the weight. Keep the object as near 

the centre of your body’s gravity as 

possible. Avoid twisting your bodies 

when carrying the unit; instead, turn 

your whole body using your feet.

Summary of Contents for G1100KU






























Reviews: