background image

8

Introduction 

Congratulations on purchasing your new spotlight. Read 

this Instruction Manual and follow the instructions carefully 

before using your new Rechargeable Spotlight. 

Charging/recharging the spotlight

This unit is shipped in a partially charged state. Charge 

unit BEFORE first use using the 240 volt AC charger for 

24 hours. Charge after each use. The charge status LED 

flashes while charging and lights solid when the unit is fully 

charged while using the AC charging method.

Charging/recharging using the 240 volt AC charger

   Make sure the spotlight is off (the trigger lock is in the off 

position and the trigger is not depressed).

   Insert the barrel connector of the plug pack charger into 

the DC Plug Pack charging socket on the back of the 

spotlight.  Insert the plug end into a standard 240V ac 

power point.

   Charge until the charge status LED lights solid 

(approximately 18-24 hours).

Charging/recharging using the 12 volt DC charger 

(optional accessory)

   Make sure the spotlight is off (the trigger lock is in the off 

position and the trigger is not depressed).

   Plug the double pin tip of the 12 volt DC charger into the 

12 volt DC charging port.

   Insert the 12 volt DC plug end into the accessory outlet of 

your vehicle or other 12 volt DC power source.

   Charge for approximately 5-7 hours..

Make sure the DC source (jump-starter, battery pack, 

vehicle accessory outlet, etc.) is 12 volt DC and is able to 

supply at least one half amp at 12 volt DC for 10 hours. 

Notes: 

When using a vehicle’s 12 volt DC accessory outlet 

as a charging source, be aware that some vehicles require 

you to turn on the ignition to power the accessory outlet.

WARNINGS:

   TO AVOID THE RISK OF PROPERTY DAMAGE, 

CHARGE UP TO 24 HOURS 

MAXIMUM

 USING THE 

AC CHARGING METHOD; UP TO 7 HOURS 

MAXIMUM

 

USING THE DC CHARGING METHOD.

   NEVER ATTEMPT TO USE THE AC CHARGER AND 

DC CHARGING PORT SIMULTANEOUSLY.

Operating instructions

Operating the spotlight

1. Disconnect from charger.
2. The On/Off trigger is located in the front of the handle of 

the spotlight.

3. To turn the spotlight on, squeeze the trigger.
4. To turn off the spotlight, release the trigger.

Note: 

The On/Off trigger can be locked in the on position 

using the trigger lock switch on the side of the unit.

Operating the unit corded

Plug the double pin tip of the 12 volt DC charger (optional 

accessory) into the 12 volt DC charging port. Insert the 12 

volt DC plug end into the accessory outlet of your vehicle or 

other 12 volt DC power source. Operate the unit as outlined 

in the previous section.

Notes: 

When using a vehicle’s 12 volt DC accessory outlet 

as a charging source, be aware that some vehicles require 

you to turn on the ignition to power the accessory outlet.

IMPORTANT:

 The spotlight will operate while the 240 volt 

AC charger is attached, but will continue to draw power 

from the unit’s acid battery and will not continue charging 

while the spotlight operates. Manufacturer recommends  

only operating the unit in corded mode using the 12 volt  

DC charger.

Care and maintenance

All batteries lose energy from self-discharge over time and 

more rapidly at higher temperatures. When the unit is not 

in use, we recommend that the battery is charged at least 

every 60 days.

Summary of Contents for RL3003













Reviews: