background image

Operating and Assembly Instructions Flexilo FLAT BOTTOM for wood pellets 
 
Safety Information 
 

Subject to technical change 

Issue 09/2016 

Page 7 of 32 

©A.B.S. Silo- und Förderanlagen GmbH 

 

2.2 

Fire prevention 

 
All fire prevention regulations must be satisfied prior to start-up. (subject to country-specific 
modifications).
 

2.3 

Earthing 

 

 
Attention! 
Let the earthing of your pellet storage area be executed by a 
specialized company.

 

 

  All conductive parts of the silo must be grounded expertly. 

  In particular the removal system, the steel frame and the connecting armature have to be 

earthed.

 

  The filling lines must also be connected conductive and grounded professionally with a 

cable (4 mm ²) to the potential equalization conductor (by a qualified electrician for 
example). 

  Especially the earthing parts have to be connected to the potential equalization and/or the 

main potential equalization with specific PA conductors.  

 

2.4 

Nameplate 

 
The nameplate stating the calculated storage capacity must 
be attached to the pellet silo at a readily visible location, e.g. 
at the filling nozzle or on one of the frame’s legs. The 
nameplate is included in the shipping documents that 
accompany Flexilo FLAT BOTTOM for wood pellets when it is 
delivered. 
 

Nameplate with calculated storage capacity 

2.5 

Maintenance 

Regular cleaning of the bearing is required to ensure continuous, trouble-free and safe 
heating operation. The fines content and the wood dust should be removed.  
 
When cleaning, please note the following: 

  Enter storage areas only when in compliance with safety regulations: Switch off 

heating and discharge system, adequately ventilate before entering.  

  Clean the removal system prior to new filling of dust and debris. Wear dust mask of 

filter class P2. 

  Heat silo sack empty regularly and clean the silo sack through movement from dust 

while the removal system is uninstalled.

 

Vacuum the storage out. In private storage, the cleaning can be done with 
commercial vacuum cleaners with HEPA filters. The vacuum cleaner should not work 
at the highest level to avoid overheating and to prevent ignition hazards. 

 

 

For reasons of occupational health and safety, an industrial vacuum cleaner with filter 

class M is required for cleaning pellet storages. Earth buried storage and all other 
storages starting at a capacity of 40 tons may only be accessed with a CO warning 
device.

 

  Until the next filling process please fill the silo manually with pellets in sacks (through 

the manual filling nozzle). 

Summary of Contents for Flexilo FLAT BOTTOM

































Reviews: