background image

25

10. 

install the factory supplied intake air and/or vent termination(s) 

using field supplied pipe and one field supplied 90° elbow as 

shown in Figure 19. The short section of pipe that connects 

between the field supplied 90° elbow and the factory supplied 

termination  must  not  be  excessive  in  length. The  exposed 

portion of this pipe shall be no more than 2 inches (5 cm), 

see Figure 19.

INTAKE AIR AND/OR VENT

TERMINATION(S) MUST BE A 

MINIMUM OF 24 INCES (60 cm) 

ABOVE ANY PARAPET, VERTICAL

WALL OR STRUCTURE WITHIN

10 FEET (3 m) HORIZONTALLY.

VERTICAL TERMINATION(S) FLAT ROOF CLEARANCE

INTAKE AIR AND/OR VENT (EXHAUST)

24 INCHES (60 cm)

MINIMUM HEIGHT ABOVE

IF LESS THAN

10 FEET (3 m)

figure 20

11. 

return to Power Vent installation on page 23 or Direct Vent 

installation on page 23 to complete the installation of the intake 

air  and/or  vent  piping  between  the  termination(s)  and  the 

water heater.

VERTICAL TERMINATION - DIRECT VENT

STANDARD TERMINATIONS

24 INCHES (61 cm) MINIMUM

48 INCHES (122 cm) IN COLDER CLIMATES

FACTORY SUPPLIED

STANDARD TERMINATIONS

POINTED DOWNWARD

FIELD

SUPPLIED

90° ELBOW

VENT (EXHAUST)

TERMINATION

INTAKE AIR

TERMINATION

FIELD SUPPLIED

PLUMBING

ROOF BOOTS

OR FLASHINGS

MAINTAIN 12” (30 cm)

18” (45 cm) FOR CANADA

MINIMUM CLEARANCE

ABOVE HIGHEST 

ANTICIPATED SNOW LEVEL.

figure 21

configuration  vertically  through  the  roof  the  following 

instructions must be followed:
The intake air and vent pipes must penetrate the same side 

of the roof as shown in Figure 21 on page 25.
The intake air and vent terminations must be oriented facing 

downward and in the same direction as shown in Figure 21 

on page 25.

The intake air and vent terminations must have a minimum 

separation of 24” (61 cm) measured on center line as shown 

in Figure 21 on page 25. in colder climates this separation 

should be increased to at least 48 inches (122 cm).
The  bottom  edge  of  the  intake  air  and  vent  terminations 

must be a minimum of 12 inches (30 cm), 18 inches (45 cm) 

in  Canada,  above  the  average  or  expected  snow  level  as 

shown in Figure 19 and Figure 21 on page 25.

6. 

When  the  intake  air  and/or  vent  piping  from  multiple 

water  heaters  will  terminate  in  the  same  location  the  vent 

terminations  can  be  grouped  together  in  close  proximity  0 

inches/touching. intake air terminations can also be grouped 

together in close proximity 0 inches/touching. 
The  distance  between  the  closest  vent  and  intake  air 

terminations  must  be  a  minimum  of  24  inches  (61  cm)  as 

shown in Figure 21. in colder climates this separation should 

be increased to at least 48 inches (122 cm).

7. 

Cut a 5 inch (13 cm) diameter hole for 4 inch pipe or 7 inch 

(18 cm) diameter hole for 6 inch pipe where the pipe(s) will 

pass through the roof.

note:

 Beware of concealed wiring and piping when cutting 

through the roof.

8. 

Suspend  the  pipe(s)  through  center  of  hole  using  field 

supplied metal strapping or equivalent support materials as 

shown in Figure 19.

2” (5 cm)

MAXIMUM

FACTORY SUPPLIED

STANDARD TERMINATION

POINTED DOWN TOWARDS

THE GROUND

VERTICAL TERMINATION(S) INSTALLATION

INTAKE AIR AND/OR VENT (EXHAUST)

FIELD

SUPPLIED

90° ELBOW

FIELD

SUPPLIED

STRAP/SUPPORT

FIELD SUPPLIED

PLUMBING

ROOF BOOT

OR FLASHING

MAINTAIN 12” (30 cm)

18” (45 cm) FOR CANADA

MINIMUM CLEARANCE

ABOVE HIGHEST ANTICIPATED

SNOW LEVEL.

figure 19

9. 

Slide  a  roof  boot  or  equivalent  flashing  over  the  pipe  and 

secure roof boot or equivalent flashing to roof (see Figure 19) 

and seal around the flashing.

Summary of Contents for 101 Series













































































Reviews: