How to use
Technical Specifications
Troubleshooting
Electrical Safety
Even though these products are designed keeping highest safety standards in
mind, there are certain Do’s and Dont’s which need to be followed while using
these products.
• Discard the first cycle of
pure water, before you
start using it for
consumption.
• Make sure to discard
the water in the storage
tank if you have not
used the purifier for
more than 2 days.
Notice
Your A. O. Smith / RO Water Purifier may not function at its desired
capability if used incorrectly. This may not necessarily mean that the product is
faulty. For instances like these, please follow the steps given below to
troubleshoot the problem without the help from a certified technician. If the
problem still persists, please call Customer care centre immediately.
Recommended input Feed water quality for the optimum
performance of your product
* Flow rates depends on variable factors such as feed water pressure, feed water characteristics
and condition of the membranes and filters.
** Recovery and TDS reduction percentages also depends on variable factors such as life and
condition of the membranes and filters, feed water pressure, feed water characteristics etc.
*** If input pressure exceeds 30 psi, a pressure reducing valve needs to be installed at the feed line.
If the pressure is lower than 7 psi, a booster pump needs to be installed. Ensure you buy them
from A. O. Smith Company authorised service technician.
Power plug must be used with a 230 V
outlet. It is recommended to connect
the product to the power supply only
with the plug that is provided with
the purifier. Do not pull out or touch
power plug with wet hands to avoid
electrical shock.
1. Turn ON the water connection
through the ball valve.
3. To dispense water from the
storage tank, push and hold the
water faucet lever.
4. To dispense water continuously,
lift up the water faucet lever for
the continuous water flow. To stop
the water flow, pull down the
water faucet lever.
2. Switch ON the power supply and
press the power button of the
purifier.
Make sure that the feed water is
tested before installation. Do not
install the product if the TDS and
Hardness are more than that
prescribed in the recommended feed
water conditions (Refer Page 12).
Product should be installed only by
A. O. Smith Company Authorised
Service Technician. Do not open the
purifier for cleaning the filters or for
any part replacements. This must be
done only by A. O. Smith Company
Authorised Service Technician.
Install the product away from direct
sunlight.
7
8
9
10
12
13
14
11
Change in water taste Has the purified water
Drain the stored water from
(All models).
been stored in the tank the storage tank through
for long time?
faucet.
RO membrane/filters
Call Customer Care Centre
may require
for RO membrane/filters
replacement. replacement.
Has the raw water
Call Customer Care Centre.
quality changed?
Check if there is no
Switch OFF the Water
water flow through
Purifier and call Customer
reject line.
Care Centre.
Decreased flow of
Check whether the tap/
Open the tap/ball valve.
purified water
ball valve is closed.
(All models).
RO membrane/filters
Call Customer Care Centre.
may be clogged or
for RO membrane/filters
damaged. replacement.
Less/No reject water
Check if the reject
Clear the bent in the reject
(All models).
Water tube is bent.
water tube.
Check if the reject
Switch OFF the Water
Water tube is blocked.
Purifier and Call Customer
Care Centre.
Less/No purified
Check whether there is
If not, take the help of a
water (All models).
water supply in the tap. plumber to set it right.
Check whether tap/ball Open the tap/ball valve.
valve is closed.
Check if either Filter
Call Customer Care Centre
change ( model
for RO membrane/filters
only) is blinking.
replacement.
None of the above.
Call Customer Care Centre.
Problems
Possible Cause(s)
Solution
Water flow
Electrical Diagram
Safety Precautions
Figure 3
Figure 4
Figure 5
Figure 5
Figure 5
Figure 5
Figure 5
Figure 5
5. To stop the water flow, pull down the
water faucet lever to position 2 slowly
and then to initial position. This avoids
splashing of water.
Figure 5
Figure 5
Figure 5
Faucet
Float Switch
Storage Tank
Pump
RO
Sediment
filter
SCB filter™
Tap water
Ball Valve
Inlet water
3-way joint
Check
Valve
Low Pressure
Switch
Inlet Solenoid
valve
Flow
Restrictor
Waste
water
Pure
water
SCM-TECH™
Faucet
Float Switch
Storage Tank
Pump
RO
Sediment
filter
SCB filter™
Tap water
Ball Valve
Inlet water
3-way joint
Check
Valve
Low Pressure
Switch
Inlet Solenoid
valve
Flow
Restrictor
Flush
Solenoid
valve
Waste
water
Pure
water
SCM-TECH™
ON
230V
CAUTION
TDS
METER
CAUTION
Parameter
Limits
Total Dissolved Solids (TDS)
Up to 2000 ppm
Total hardness
Up to 500 ppm
Turbidity
Up to 5 NTU
Iron
0.3 ppm (max.)
Feed water pressure
5 psi to 30 psi
Feed water temperature
5°C to 45°C
RECOMMENDED FEED WATER QUALITY
SMPS
24 VDC
LPS
HPS
High water
level
GND
150V - 300V
50 Hz AC
P
N
Pump
Inlet
SV
LPS
Pump
SMPS
Inlet
SV
High
water
level
switch
Flush
SV
Display
PCB
150V - 300V
50 Hz
1- f AC supply
P
N
Main Control Board
24V DC
GND
Position 1
Position 2
Position 3
Product Dimensions (H x D x W)
460 mm x 260 mm x 380 mm
Net Weight
8.5 kgs (approx.)
Gross Weight
10 kgs (approx.)
Flow rate*
Upto 15 litres per hour
Storage tank capacity
5 litres (approx.)
Purification technology
RO (Reverse Osmosis)
6 Stage Purifying Technology
Sediment SCB filter (Sediment
Carbon block) + Side Stream RO
me SCM-TECH filter (Silver
Activated Post MIN-TECH)
Membrane type
Thin film composite RO membrane
Material of construction for
Food safe, non-toxic, engineering grade
plastic parts
plastics
Pump type
Diaphragm pump, 24VDC, 0.26 Amps,
Operating Pressure 125 psi (Max.)
Input Voltage
150 – 300 VAC, 50 Hz
Power rating (Max)
48 Watts
Pressure Rating***
5 psi to 30 psi
% Recovery**
Upto 30%
TDS reduction**
≥95% (approx.)
Input water temperature
5°C to 45°C
Model
A. O. Smith /
Tank full LED blinks
Over flow error.
Switch OFF the Water
continuously
Purifier and call Customer
(For model).
Care Centre.
Power LED blinks
Low pressure alarm is
Check feed water supply
continuously
triggered indicating
to the purifier. If problem
(For model).
that the system input
still persists, switch OFF
water pressure is not
the Water Purifier and call
in the required range.
Customer Care Centre.
Flush LED blinks
RTC error.
Switch OFF the Water
continuously
Purifier and call Customer
(For model).
Care Centre.
Filter change LED
RO membrane or filters Call Customer Care Centre
blinks and unit is
life is about to ends.
for RO membrane or filters
functioning
replacement.
(For model).
Filter change LED
RO membrane or filters Switch OFF the Water
blinks and unit is not life ends.
Purifier and call Customer
functioning
Care Centre RO membrane
(For model).
or filters replacement.
Problems
Possible Cause(s)
Solution