background image

20

A44-P

8.  SPARE PARTS

8.1  SPARE PARTS LIST

Even though the  machine has been submitted to several tests and functional checks, we listed below the components that 

we suggest you to have a minimum and sufficient set of. This will help guarantee the shortest possible downtime.

TABLE  8.1 - A

COMPONENT

•  WEDGES DRIVER BLADE 

•  WEDGES CLAW-HEADS 

•  “L” SHAPED SUPPORT (WEDGES GUIDE) 

•  VALVES-REDUCERS-REGULATORS 

•  VERTICAL AND HORIZONTAL CLAMPING 

•  GASKETS

8.2  SPARE PARTS ORDERING

We remind you that only a qualified technician can repair the machine.

Therefore we suggest the intervention of your local distributor or A-Plus Automation Center of Technical Assistance, which 

has access to qualified staff, proper equipment and tools, and who uses original spare parts.

To order the above spare parts, send the following data by fax, e-mail or letter: 

•  Model of the Machine

•  Code of drawing scheme

•  Reference number of spare part or group indicated on the mechanical drawing

•  Code number of single or group spare part

9.  MACHINE DEMOLITION

9.1  MACHINE DEMOLITION

When scrapping the machine, group components by chemical composition and dispose of separately in accordance with 

applicable legislation. Do not dispose of non-biodegradable materials, lubricant oils and non-ferrous articles (rubber, PVC, 

plastics etc.) in the environment. 

10. ATTACHMENTS

10.1 DECLARATIONS

You can find here attached the following declarations

•  Declaration of conformity to the Norm 89/392/CEE

10.2 SCHEMATICS 

You can find here attached the following schemes:

•  (A) Mechanical Schematic

•  (B) Pneumatic Schematic

•  (C) Plate locations

•  (D) Sharpening Table

Summary of Contents for A44-P

































Reviews: