background image

8

  Notices

 Note: This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or more of the 
following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

  Consult the dealer or an experienced radio/TV technician for help. Changes or 
modifications not expressly approved by the party responsible for compliance 
could void the user’s authority to operate this equipment

 This device contains licence-exempt transmitters(s)/receiver(s) that comply with 
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).  
Operation is subject to the following two conditions:

This device may not cause interference.

 This device must accept any interference, including interference that may cause
undesired operation of the device.

 Cet appareil contient des émetteurs/récepteurs exemptés de licence conformes à 
la norme Innovation, Sciences, et Développement économique Canada.  
L’exploitation est autorisée aux deux conditions suivantes:

L’appareil ne doit pas produire de brouillage.

 L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.

6

Summary of Contents for ADC-V523











Reviews: