background image

AAF International Plant Locations

AAF, the world’s largest manufacturer of air 
filtration solutions, operates production, 
warehousing and distribution facilities in 22 
countries across four continents. With its 
global headquarters in Louisville, Kentucky, 
AAF is committed to protecting people, 
processes and systems through the 
development and manufacturing of the 
highest quality air filters, filtration equipment, 
and associated housing and hardware 
available today.

Contact your local AAF Flanders representative 
for a compete list of AAF Flanders Air Filtration 
Product Solutiobns.

Americas

Louisville, KY
Atlanta, GA
Ardmore, OK
Bartow, FL
Columbia, MO
Fayetteville, AR
Hudson, NY
Momence, IL
Smithfield, NC
Tijuana, Mexico
Votorantim, Brazil
Washington, NC

Europe

Cramlington, UK
Gasny, France
Vitoria, Spain
Ecoparc, France
Trencin, Slovakia
Vadstena, Sweden
Vantas, Finland

Asia & Middle East

Riyadh, Saudi Arabia
Shah Alam, Malaysia
Suzhou, China
Shenzhen, China
Miaoli, Taiwan
Bangalore, India
Noida, India
Yuki, Japan (Nippon Muki)

For Technical or Application Questions:

Phone: 1 (888) 223-2003
Email: productsupport@aafintl.com 

9920 Corporate Campus Drive, Suite 2200, Louisville, KY 40223-5690    

888.223.2003  Fax 888.223.6500  |  aafintl.com  

AAF Flanders has a policy of continuous product 

research and improvement. We reserve the right 

to change design and specifications without notice.

ISO Certified Firm                    

©2020 AAF International and its affiliated companies.

AFP-3-103     12/20

Summary of Contents for AstroFan EC FFU



















Reviews: