AAF FabriPulse M Installation, Operation And Maintenance Manual Download

Page: 12 / 37

FabriPulse

2015 American Air Filter Company, Inc. Any use of the text or

images this document contains, without permission of American Air

Filter Company, Inc., is prohibited. FabriPulse, AAF, REDClean,

REDFiltration, and Reliable Efficient Durable are registered

trademarks of American Air Filter Company, Inc. d/b/a AAF

International.

PRODUCT SHIPMENT

Unless otherwise defined in the purchase order and agreed by AAF, the

FabriPulse M is arranged and palletized for domestic transit and shipped FOB the

AAF factory. The method of shipment will be as specified in the customer’s

purchase order to AAF.

4.1

How the product ships

All of the FabriPulse M dust collectors are shipped factory assembled

requiring only:

•

Assembly of hopper section to housing on sizes 336 and 420

•

Field bolting of the legs and braces

•

Connection of ductwork and/or the fan

•

Connection of hopper discharge device(s)

•

Mounting and wiring of the control box

•

Connection of compressed air supply

•

Differential and air pressure gauge connections

4.2

Items that ship separately

To save the customer money, AAF International may ship items separately.

The customer will be notified of which equipment ships separately when the order

is placed. Items that ship separately should be set aside in an area that is clean,

dry, and in a place where damage to the equipment will not occur.

PRODUCT RECEIPT AT THE DESIGNATED DELIVERY POINT

5.1

Responsibilities of the customer or customer’s agent

Ensure all loading/unloading equipment and safety equipment is on site at

the time of delivery. Safe and efficient operation of the collector depends on

proper installation. Know proper codes and regulations before installation starts.

5.2

Receiving

Remove crates, tarps, shipping straps, etc. along with any loose items or

equipment before unloading the FabriPulse M.

5.3

Inspection on arrival

The FabriPulse M is normally shipped by truck and should be checked for

damage that may have occurred in route. Compare the collector(s) received to the

description and/or drawing of the collector(s) ordered. Report any differences or

missing items from the order to AAF International. Remove loose items or

components before lifting the collector from the truck.

Summary of Contents for FabriPulse M






































Search results

Summary of Contents for FabriPulse M

Reviews:

Related manuals for FabriPulse M

Brands by name

Popular brands

AAF FabriPulse M, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for FabriPulse M

Reviews:

Related manuals for FabriPulse M

Brands by name

Popular brands