AAF FabriPulse M Installation, Operation And Maintenance Manual Download | Manualshive

Page: 23 / 37

background image

23

FabriPulse

®

M

©

2015 American Air Filter Company, Inc. Any use of the text or

images this document contains, without permission of American Air

Filter Company, Inc., is prohibited. FabriPulse, AAF, REDClean,

REDFiltration, and Reliable Efficient Durable are registered

trademarks of American Air Filter Company, Inc. d/b/a AAF

International.

10

EXPLOSION VENTS

The following only applies to AAF-supplied explosion vents. Additional and/or

different steps, equipment, etc. may be needed for vents and other equipment not

supplied by AAF. Further, the following is a non-exhaustive list of

recommendations, and users must carefully read, among other things, the

manufacturer’s explosion vent guide for further instructions.

10.1

Installation of the Explosion Vent

If an explosion vent is ordered with the FabriPulse M, the explosion vent is

shipped separately from the collector. Ensure no damage has been done to the

explosion vent during shipping or handling.

The FabriPulse M will have a frame constructed as part of the unit where the

explosion vent is mounted. The number of explosion vents and location of the

explosion vent will be detailed on the collector drawing.

10.2

Assembly

Ensure no damage has been done to the explosion vent during shipping or

handling. The FabriPulse M will have a frame constructed as part of the unit where

the explosion vent is mounted. The number of explosion vents and location of the

explosion vent will be detailed on the collector drawing.

Gripping the opposite sides, carefully remove the explosion vent from the

crate that it was shipped. Avoid excessive flexure of the explosion vent while

handling.

CAUTION: The edges of the explosion vent can be sharp.

CAUTION: Incorrect installation of the explosion vent can cause the panel

to not open at the rated burst pressure.

Place the explosion vent over the protruding bolt holes of the frame. Make

certain the dome is protruding outwards. Install the outlet frame.

Install bolts and nuts and tighten to 20-25 ft-lbs per manufacturer’s

recommendation.

«
...
21
22
23
24
25
...
»

Summary of Contents for FabriPulse M






































Reviews:

No comments

Related manuals for FabriPulse M

Brand: Grizzly Pages: 37

Brand: Grizzly Pages: 40

Brand: Grizzly Pages: 52

Brand: Grizzly Pages: 64

Brand: Baileigh Pages: 28

Air Powered ATEX Series

Brand: Nederman Pages: 28

Brand: Grizzly Pages: 36

Brand: Grizzly Pages: 40

Brand: Grizzly Pages: 45

Brand: Grizzly Pages: 52

Brand: Grizzly Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands