background image

 

16                                                              

 

RotoClone

®

 W 

 

© 2015 American Air Filter Company, Inc. Any use of the text or images 

this document contains, without permission of American Air Filter 

Company, Inc., is prohibited. RotoClone, AAF, REDClean, REDFiltration, 

and Reliable Efficient Durable are registered trademarks of American Air 

Filter Company, Inc. d/b/a AAF International. 

 

4

 

PRODUCT SHIPMENT 

4.1

 

How the product ships 

Typically,  size  24  and  smaller  RotoClone  W  dust  collectors  will  ship  upright 

on a wooden skid. Larger sizes will ship on 4x4 wooden runners. Size 16 units and 

smaller will ship using LTL (less than truckload shipping) unless otherwise agreed 
with the buyer. Consult AAF International for information on carrier arrangements 

for all larger sizes.  

 

4.2

 

Items that ship separately 

To reduce freight costs, AAF International may ship some items separately. 

The  customer  will  be  notified  which  particular  equipment  items  ship  separately 
when the order is placed. Items that ship separately may arrive at the designated 

receipt point at different times. Those items that arrive early should be set aside in 
an  area  that  is  clean,  dry,  and  secure,  where  the  equipment  will  be  safe  and 

protected.   

 

5

 

PRODUCT RECEIPT AT THE DESIGNATED DELIVERY POINT 

The people of AAF International take pride in the quality of the products that 

we supply and it is our intention that our customer’s experience with our products 

and  services  be  positive  and  satisfying.  This  process  includes  delivery.  It  is 
important  to  ensure  that  the  product  delivered  is  what  was  ordered  and  that  it 

arrives at its destination in perfect condition. Adequate preparation on the part of 
the buyer together with a structured approach to receipt and inspection will ensure 

that  if  problems  exist  they  are  communicated  swiftly  and  efficiently  through  the 
proper channels allowing them to be resolved in the shortest possible time. 

 

5.1

 

Responsibilities of the customer or the customer’s agent 

Ensure  all  loading/unloading  equipment  and  safety  equipment  is  on  site  at 

the  time  of  delivery.  Safe  and  efficient  operation  of  the  collector  depends  on 

proper installation. Know and fully understand all laws, codes and regulations that 
apply before installation starts.  

 

5.2

 

Receiving 

Remove  crates,  tarps,  shipping  straps,  etc.  along  with  any  loose  items  or 

equipment before unloading the AAF RotoClone W. 

  

 

5.3

 

Inspection on arrival 

The  AAF  RotoClone  W  is  normally  shipped  by  truck  and  should  be  checked 

for damage that may have occurred in route. Compare the product received to the 

Summary of Contents for RotoClone W















































Reviews: