background image

12

APPENDIX 2

WARRANTY

NOTE:  Follow Return Procedures In Section 1.3.

Aalborg

®

SMV motorized valves are warranted against parts and

workmanship for a period of one year from the date of purchase. It
is assumed that equipment selected by the customer is construct-
ed of materials compatible with gases or liquids used. Proper
selection is the responsibility of the customer. It is understood that
gases under pressure present inherent hazards to the user and to
equipment, and it is deemed the responsibility of the customer that
only operators with basic knowledge of the equipment and its limi-
tations are permitted to control and operate the equipment covered
by this warranty. Anything to the contrary will automatically void the
liability of Aalborg

®

and the provisions of this warranty. Defective

products will be repaired or replaced solely at the discretion of
Aalborg

®

at no charge. Shipping charges are to be borne by the

customer. This warranty is void if the equipment is damaged by
accident or misuse, or has been repaired or modified by anyone
other than Aalborg

®

or factory authorized service facility. This war-

ranty defines the obligation of Aalborg

®

and no other warranties

expressed or implied are recognized.

Summary of Contents for SMV
















Reviews: