background image

 

Operators and Maintenance Manual 

 

Measuring module

 

EMS DAQ R02.01

 

Page 

18/18

 

 

Copyright: 

Auto & Aero Technologies Sp. z o.o. 

Mazowiecka 10/5, 20-723 Lublin, Poland  

 email: info@aatech.pl 

  

www.aatech.pl 

 

 

 

The  information  in  this  document  is  subject  to  change  without  notice  and  should 
not be construed as commitment by Auto & Aero Technologies Sp. z o.o. 

These technical data and the information embfromied therein are the property of 
Auto & Aero Technologies Sp. z o.o., and shall not, without prior written permission 
of  Auto  &  Aero  Technologies  Sp.  z  o.o.,  be  disclosed  in  whole  or  in  part  to  third 
parties.  This  statement  shall  be  included  on  any  reprfromuction  of  these  data,  in 
whole or in part. The Manual must remain with the engine/aircraft in case of sale. 
 
 
 
 
 

Copyright 2017 © 

- all rights reserved. 

 
Other names in this documentation are used purely for  ease of identification and 
may be trademarks of the respective company or owner. 
Approval of translation has been done to best knowledge and judgement  - in any 
case the original text in English language is authoritative. 

 

 

Summary of Contents for EMS DAQ R02.01



















Reviews: