background image

 

 

3.

 

Packing List 

 

GXM

-

04

/

GXL

-

04 ... Mini DIN connector (8 pin, plug) 

Cable with connector (AX-KO5692) 

Cable length: 1.5 m 

This manual 

 
 

GXM

-

06

/

GXL

-

06 ... Screwdriver for adjustment 

Mini DIN connector (4 pin, plug) 

Cable with connector (AX-KO5692) 

Cable length: 1.5 m 

This manual 

 

 

4.

 

Installing the Option 

Caution

 

Disconnect the AC adaptor before installing the option to the balance. 

 

4.1.

 

Installing the GXM-04/GXM-06 

 

Install the GXM

-

04 and GXM

-

06 according to the following procedure. 

 

(The installation procedure of the GXM

-

04 and GXM

-

06 is the same.)

 

 

Step1  Remove the two screws from the panel and remove 

the RS-232C

/

USB board from the balance.

 

 

Step2  Pull gently and remove the two cables 

from the RS-232C

/

USB board.

  

 
 
 
 
 

Step3  Insert the two cables into the sockets of the GXM

-

06 board.

 

 

Step4  Insert the rubber packing and plug the GXM

-

06 into 

the balance.

 

Screw the panel of GXM

-

06. 

 
 
 
 
 

Caution 

 

 

When inserting the GXM

-

06, pay attention to the top and bottom orientation of the board.

 

 

 

The rubber packing has a deep groove on the balance side. 

 

RS

-

232C

/

USB board 

Cable 

Rubber packing 

Connector with lock 

Screw 

Rubber packing 

Cable 

Connector 

GXM

-

06 board 

Summary of Contents for GX-L Series

























Reviews: